 | | I'm doing the revolving/"secret" door parts
|
|
I'm calling "dibs" on the following: 30101.dat, "Panel 2 x 8 x 6 Revolving Frame" 30102.dat (30344.dat?), "Panel 2 x 8 x 6 Revolving Door" 30102p01.dat, "Panel 2 x 8 x 6 Revolving Door - Ninja pattern" These were the best names I could think of. I'm (...) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
(...) I recomend using 30102 because both 30101.dat, the frame and the door would have been created at the same time so it would fit that they would use part numbers that are next to each other. (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
(...) How about: 30101.DAT Door 2 x 8 x 6 Frame Revolving 30102.DAT Door 2 x 8 x 6 Revolving 30102P01.DAT Door 2 x 8 x 6 Revolving with Ninja Pattern I'm not keen on using themes in part names, but in this case, I can't think of a better name. (...) (...) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
(...) So, you're saying these should be of the "Door" CATEGORY, and not of the "Panel" CATEGORY? I'm not sure I agree, 'cuz this meta-part assembly is supposed to be a _wall_ (i.e., a panel) that just _happens_ to include a secret/revolving door. In (...) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
"Steve Bliss" <steve.bliss@home.com> wrote in message news:6snl0t4tiaba1eo...4ax.com... [snip] (...) Weren't (...) I first saw them in the 1997 Fright Knights set 6087 (Witch's Magic Manor). --Travis Cobbs (tcobbs@san.REMOVE.rr.com) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts [DAT]
|
|
(...) Nah, it's just a hidden door, with a frame. Just like any other door-in-frame assembly. Just my opinion, of course. (...) Hmm. This *could* call for a "~Moved to" file, but "~Moved to"'s have historically been caused by corrections within the (...) (24 years ago, 10-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
(...) The only other occurance of this type that I am aware of is the bucket lids. Some of these have two moulded on numbers, which are clearly part numbers. I've been advised in the past that this was because the large LEGO / DUPLO logos are (...) (24 years ago, 11-Nov-00, to lugnet.cad.dev)
|
| |
| | Re: I'm doing the revolving/"secret" door parts
|
|
(...) I'm not sure. Other than the printing, I don't know of any other post-mold processing that would be done on this part. One of the numbers on the Ninja door panel looked suspiciously like it had been imprinted on the door at some time after the (...) (24 years ago, 13-Nov-00, to lugnet.cad.dev)
|
