Subject:
|
Re: I'm doing the revolving/"secret" door parts
|
Newsgroups:
|
lugnet.cad.dev
|
Date:
|
Thu, 9 Nov 2000 17:43:11 GMT
|
Viewed:
|
723 times
|
| |
|
|
In lugnet.cad.dev, Franklin W. Cain wrote:
> 30101.dat,
> "Panel 2 x 8 x 6 Revolving Frame"
>
> 30102.dat (30344.dat?),
> "Panel 2 x 8 x 6 Revolving Door"
>
> 30102p01.dat,
> "Panel 2 x 8 x 6 Revolving Door - Ninja pattern"
>
> These were the best names I could think of.
> I'm listing the "door" piece with the _FRAME_'s dimensions,
> even though the door is actually smaller than this,
> 'cuz the door piece isn't usable just by itself
> and must be inserted into the frame piece.
How about:
30101.DAT Door 2 x 8 x 6 Frame Revolving
30102.DAT Door 2 x 8 x 6 Revolving
30102P01.DAT Door 2 x 8 x 6 Revolving with Ninja Pattern
I'm not keen on using themes in part names, but in this case, I can't think
of a better name.
> The "door" piece as two different numbers stamped on it.
> Which one do I use? (I listed both of them above.)
Yuck. That's bad. For those of you at home, Franklin is absolutely right.
If you look on the bottom of the door part, there are two part numbers,
right next to each other (but far enough apart, and with a different
type-style, that it's obvious they aren't actually one big number).
There's no way this could be a situation of two molded parts which are
welded/glued together later.
Maybe the 30102 was rebranded, when the Ninja print was put on it. Weren't
these pieces new with Ninja? The numbering seems to indicate they were
designed at the same time as the Wild West pieces.
For now, go with 30102, and I'll check my sources...
Steve
|
|
Message has 3 Replies:
 | | Re: I'm doing the revolving/"secret" door parts
|
| (...) So, you're saying these should be of the "Door" CATEGORY, and not of the "Panel" CATEGORY? I'm not sure I agree, 'cuz this meta-part assembly is supposed to be a _wall_ (i.e., a panel) that just _happens_ to include a secret/revolving door. In (...) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
| | | Re: I'm doing the revolving/"secret" door parts
|
| "Steve Bliss" <steve.bliss@home.com> wrote in message news:6snl0t4tiaba1eo...4ax.com... [snip] (...) Weren't (...) I first saw them in the 1997 Fright Knights set 6087 (Witch's Magic Manor). --Travis Cobbs (tcobbs@san.REMOVE.rr.com) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
| | | Re: I'm doing the revolving/"secret" door parts
|
| (...) The only other occurance of this type that I am aware of is the bucket lids. Some of these have two moulded on numbers, which are clearly part numbers. I've been advised in the past that this was because the large LEGO / DUPLO logos are (...) (24 years ago, 11-Nov-00, to lugnet.cad.dev)
|
Message is in Reply To:
| | I'm doing the revolving/"secret" door parts
|
| I'm calling "dibs" on the following: 30101.dat, "Panel 2 x 8 x 6 Revolving Frame" 30102.dat (30344.dat?), "Panel 2 x 8 x 6 Revolving Door" 30102p01.dat, "Panel 2 x 8 x 6 Revolving Door - Ninja pattern" These were the best names I could think of. I'm (...) (24 years ago, 9-Nov-00, to lugnet.cad.dev)
|
8 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
