 | | Re: BFC: LITS 2
|
|
(...) Oh, good. :) I wasn't sure before, but after posting a follow-up to John today, I figured it out. Now, about those transparent parts with decorations... Steve (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: BFC: LITS 2
|
|
(...) I think we're using different meanings here. By 'local clipping', I mean the clip-setting in a subfile disappears when that subfile is finished. It is not carried back up to the superfile, and it is not reinstated if the same subfile is used (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: BFC: LITS 2
|
|
(...) Unless we have a solution to the invert case, the document's assertion is correct. (...) I think you are correct that NOWIND/UNKNOWN is not important/needed. For now, let's proceed assuming that decorations will be handled by using NOCLIP or (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: BFC: LITS 2
|
|
(...) I've kept thinking about it, and I don't see a solution. There are some algorithms that can figure out the normal/inverted question in some cases, but these algorithms would be too slow to implement in a rendering program. And they are not (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: 71184 Bar 4.5L Straight is too short
|
|
(...) I don't have the fix, but I did locate it on lugnet.cad.dat.parts. Normally, I'd require you to e-mail me the fix before I'd put it in an official release, but since you're a good modeler, I'll let it go this once. Just don't tell anyone. ;) (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Some Words To BFC
|
|
(...) OK, here's a counter-proposal: don't require all parts/primitives to be BFC'able, and allow both BFC-ready and BFC-not-ready files in the same rendering. This reintroduces the concept of having a single meta-statement at the start of each (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Performance Improvement [DAT]
|
|
(...) As I said before, in this case it's more correct to use 3-4disc primitive, to avoid the T type juntions. (...) Yes, cracks may appear ! Same problem like in a T type junction But has someone said, nothing like real/concrete testing, so here (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Performance Improvement
|
|
Steve: (...) I can't see how Rui's suggested change gives any problems at all and I don't mind a few percent speed increase. (...) And? Does the "diameter line" not cross the radius? If there is a significant risk of a misalignment, then we (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Some Words To BFC
|
|
On Fri, 7 Apr 2000, Leonardo Zide wrote: [...SNIP...] (...) Actually I think you missunderstood something (or maybe I did), but the 0 INVERSE meta command is to be used ONLY with file references, that is: 0 INVERSE 1 16 x y z a b c d e f g h i (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: BFC checking program (was Re: Some Words To BFC)
|
|
I seem to be missing a required .dll file: MFC42D.DLL. Can you send this, or can I find it somewhere else? -John Van (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
