 | | Re: Voting Page
|
|
Steve Bliss <blisses@worldnet.att.net> wrote in message news:3741a938.209688...net.com... (...) some (...) fix (...) everyone.. (...) Inlining primitives with type 5 lines works fine. But at least sometimes inlining a subpart has turned the type 5 (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
Is there already a button for this? It had odd results when I tried it long ago IIRC. -John Van Steve Bliss <blisses@worldnet.att.net> wrote in message news:3741a8a1.208175...net.com... (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page
|
|
(...) Hmm. I don't remember hearing about this problem before. Probably did, and it fell out of my brain. I will look into the LDAO/inline code, and see what's up. Steve (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) I've thought about writing a function in LDAO to sort a DAT file by line-type: first the 2 (edges) and 5 (conditionals), then the 1 (may be edges, surfaces, or both) then the 3 (triangles) and 4 (quads). Steve (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part Name Question
|
|
(...) I like Bar or support. Those, IMO, are the most-likely non-space use of it. (...) Will the 1x1 end of it use capitalization? (i.e. STUD.DAT) Also, a problem that I noticed with John's mock-up is that the end cylinder was *not* the same (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Part Name Question
|
|
I'm finalizing the "Star Wars Ion Cannon" part, and neither John nor I can think of a decent name for it. Heck, what *category* should it be in? John has suggested one of the following categories: Bar Support Space And I've got the following (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) Speaking as the author of this part, I like the idea of using the word "Bogie" in the description. But also I would like to express in the name that you normally clip this part on the side of the train motor. So I would prefer the following (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) Either of these is fine with me. (...) The 'without corners' name follows the precedent of existing LDraw pieces: 2450.DAT Plate 3 x 3 without Corner 2419.DAT Plate 3 x 6 without Corners 6106.DAT Plate 6 x 6 without Corner 2401.DAT Plate 10 x (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) You can minimize the jagged appearance by using a 1-8cyli.dat around the hole. This leaves the minimum amount of surface around the holes to be jagged in POV-Ray. And if you rotate all the primitives to center your 1-8cyli parts on the (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Part 2429
|
|
What happened to this part (used to be Hinge Plate 1 X 4 Bottom)? Part 146, Window 1 x 2 x 3 Pane Latticed, was move to this number (2429) in the last update, but I cannot find the original 2429. Does anyone have any answers, or did I just miss (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
