 | | Re: part: baseplate 33 x 32 road curve with road pattern-9 studs
|
|
(...) Thanks Todd! I can finally post large DAT files without worrying that chunks will be left out (eg, my truck). --Bram (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: M-Peedy v1.0 released
|
|
Just a note for the installation instructions.I always need to make a new tool with the same name as the block in the ini file(in this case, M-Peedy), before I click update tools, and after I put the block in the dat file.The settings automatically (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: Quad intersections
|
|
Dave, Thank you very much! This will help me on some parts-work I was avoiding, just because I didn't want to figure out these intersections. I'm planning on uploading a spreadsheet with some basic interpolation and intersection templates. Do you (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: parts DESPERATLY wanted (steve: please read)
|
|
(...) Umm, I must have misunderstood here. Based on Manfred's response, I thought you meant that the new green roadplates had the same printing as the previous gray plates. I checked, and this is impossible, because the new green plates have 8 studs (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: baseplate 32 x 32 road curve with road pattern-9 studs
|
|
thanks for the photo... the only thing i noticed was that the white line is briken in that one but not in the one i was working from (set #6321). the piece appears to be finished and i will submit it for voting in vote99-03. (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | RE: Quad intersections
|
|
Hi Steve, I've been lurking for a while and thought your post was interesting enough to figure it out. I brushed off my Calculus text book, and after a page and a half of algebra, and remembering what determinants and cross products are all about I (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: baseplate 32 x 32 road curve with road pattern-9 studs
|
|
(...) Well, hey, that's not so bad -- the resulting news article was 34986 bytes. (...) Tell you what. Here's a photo of the element: (URL) photo is a bit grainy, but it is dark outside and the only easily available illumination I had was a (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: part: baseplate 33 x 32 road curve with road pattern-9 studs
|
|
(...) Yes, I think Netscape imposes something like a 32K or 128K limit on the <TEXTAREA> tag. It's also set to a max of 65000 characters in the HTML code, so even if Netscape didn't impose a limit, the web page would. Strictly speaking, News-by-Mail (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: How much is too much?
|
|
(...) Very nice. I like some of your models. It is also nice having pictures for different angles. I didn't read through the text, but it looks like you put quite a bit of time into making the pages. Good job :) Ryan "Build or build not. There is no (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: Part Request: 30200
|
|
(...) Ok, I've got my calipers here, and I'm reading .1325 inches in diameter. I plug that figure into my trusty HP28S and get a conversion to 3.3655mm, and half of that is 1.68275mm radius. I'll leave the conversion to LDUs to you :) --Karim (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: Part Request: 30200
|
|
(...) Ok, I've got my calipers here, and I'm reading .1325 inches. I plug that figure into my trusty HP28S and get a conversion to 3.3655mm. I'll leave the conversion to LDUs to you :) --Karim (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: part: baseplate 33 x 32 road curve with road pattern-9 studs
|
|
i do not think it was a limit on lugnet.cad.dat. i think it may have been a limit on netscape's text control. since i use netscape for browsing the group, i cant post it. i cant get the NNTP and i do not want the Mailing list so i can't post it. if (...) (26 years ago, 5-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: Complete list of metacommands?
|
|
LDS is LDraw Script, a pre-processor for .dat files that has commands like EXTRUDE and iterative loops. I'm afraid I don't have a URL, but it should not be too hard to find. The syntax of the INCLUDE directive will be defined when I release it, but (...) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: part: baseplate 33 x 32 road curve with road pattern-9 studs
|
|
(...) Hmm, did your newsreader give you an error when you tried to post it? How big is it? 2358P01.DAT is 23518 bytes; yours must be about ~30000 bytes? That's perfectly fine to post. You could even post something as big as 3470.DAT (177792 bytes) (...) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | M-Peedy v1.0 released
|
|
sorry for the delay.. but i just started a new job and *all* of my time has been devoted to settling in there... M-Peedy version 1.0 is finally ready for the public... it merges any .DAT files (and all subfiles listed therein) into a single .MPD (...) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: How big is your VEC dir?
|
|
(...) Never noticed any slowdown. I throw my LDraw folder around so much that I always convert my VEC dir to gif to save time on the transfer. (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | part: baseplate 33 x 32 road curve with road pattern-9 studs
|
|
i have made this part but it is too big to post to lugnet.cad.dat so if anyone wants it let me know. i am especially looking for someone who has this part to check it for me. (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: How big is your VEC dir?
|
|
:-)) -- Anders Isaksson, Sweden BlockCAD: (2 URLs) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: How big is your VEC dir?
|
|
(...) Oops. Sorry Anders! --Bram Bram Lambrecht / o o \ BramL@juno.com ---...---oooo-----(_...o---...--- WWW: (URL) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
| |
| | Re: Part Request: 30200
|
|
(...) Cool! After reading that lengthy webpage that details the Falcon, I'm going to try to rework the design to more accurately model the ship. (...) Wow. I'm so pleased hear that i've had such an impact, if indirectly :) I don't have children (...) (26 years ago, 4-Apr-99, to lugnet.cad.dev)
|
