 | | Re: does anyone have a way to do rubber bands and belts?
|
|
Thanks for the info. I am accually ldrawing the 8480 space shuttle and that has some rubber belts in it. (24 years ago, 5-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: MOTM entrance question
|
|
(...) I doubt anyone would have a problem with it... -Shiri (24 years ago, 4-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
(...) I use the ldglite as my default viewer, and as we all know it's just a thin port of the ldlite 1.6 source. I know I'm looking forward to some of these new goodies and I think there might be one or two other linux/BSD/*nix users out there who (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: does anyone have a way to do rubber bands and belts?
|
|
You can use Ldraw-mode to model any curved parts. If you use it to model the technic flexible hose (not the ribbed kind), then the "inner" cylinder used for the subpart is the correct diameter for the belts. I just created a belt to go between two (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: License - again
|
|
(...) I still couldn't understand what do you call "contributor's license". The way I understand it is that when someone submits a part to the voting process, they are allowing it to be redistributed under the "redistribution license". I don't see (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: License - again
|
|
The only problem is, this license is no use without an Authors/Contributors license to go with it. And I think this is one is *too* brief. Steve (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
I use it in conjunction with LDAO, and stand-alone sometimes. What I'd most like to see is an option to automatically scale and center the model. And, like Steve (I think) said, to crop saved images to the model boundaries to save space. Thanks, (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: MOTM entrance question
|
|
(...) Huh? Do you really think otherwise? (...) Really no need for it. Selçuk (24 years ago, 4-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM entrance question
|
|
If the resulting votes yield a close call, will we be able to request *hand recounts*? Sorry, I has to say it! :) -- ---...--- Brian J. Sayatovic mailto:trin@1.net (replace '1' with 'one') "Terry K" <legoverse@yahoo.com> wrote in message (...) (24 years ago, 4-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Part description help request
|
|
(...) For the CATEGORY, I recommentd either "Boat" or "Minifig Accessory". Depending on which CATEGORY you use, that will determine the first word of the DESCRIPTION. For KEYWORDS, I recommend the following: cannon, cannons, cannonade, "black (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: MOTM entrance question
|
|
Terry K skrev i meddelandet ... (...) No objection. -- Anders Isaksson, Sweden BlockCAD: (2 URLs) (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Winner of the December 2000 ldraw MOTM is.......
|
|
Terry K skrev i meddelandet ... (...) What about dial-up connections that get a new IP number each time - how do the ISP's reuse those numbers? First caller after my logoff get's the same IP as I had? Each modem at the ISP has a dedicated IP? (I (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM entrance question
|
|
(...) (third time the charm?) No issues... I would love to see some entries from you! ++Lar (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM entrance question
|
|
(...) (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Part description help request
|
|
Hello everyone, I am just about finished with two new parts. The "Pirate" cannon (then non shooting one) and it's base piece. I would like some suggestions on a good part description, keywords and a category. They are available for viewing at my "in (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Fiber Optics module
|
|
Has anyone else noticed that the axle hole on this .dat file is 2 ldu higher than it should be? It would be great if someone else with this part could confirm this. -John Van (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: MOTM entrance question
|
|
I would trust you. Terry K <legoverse@yahoo.com> wrote in message news:G4yK5F.8F5@lugnet.com... (...) some (...) Or (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM entrance question
|
|
"Terry K" <legoverse@yahoo.com> wrote in message news:G4yK5F.8F5@lugnet.com... (...) some (...) Or (...) I wouldn't have a problem with it. -- Tim Courtney - tim@zacktron.com (URL) - Centralized LDraw Resources (URL) - Zacktron Alliance ICQ: (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | MOTM entrance question
|
|
Hi all, Just a quick survey of opinion. Given the fact that I oversee the voting, is there any objection to me submitting an entry in the MOTM? Am I trustworthy enough to handle it, or would it be preferable to have some oversight of the results? (...) (24 years ago, 2-Dec-00, to lugnet.announce, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Winner of the December 2000 ldraw MOTM is.......
|
|
(...) The parallels to the US election are just *too* sweet:-) But I see that this time the Gore gone won. <g, d, r> -John (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev.org.ldraw)
|
