 | | Re: Voting Comments
|
|
(...) Order of drawing doesn't matter, except for coincident objects. For transparent surfaces vs. edges, it matters even less: the edge must 'show through' the surface, or the renderer isn't working right. LDraw and LDLite both display transparent (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) out (...) I mean the quote taken from your previous message: "Another, somewhat similar, piece is the famous '3x4 notched trapezoid'. Unfortunately, this piece has a wholly dissimilar name: 4859.DAT Wedge 3 x 4 Plate" I just wanted to mean (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: ERROR in lcad9903 update
|
|
(...) Starting to look like a one-man thread..... Don't forget to run mklist after getting the fixed files. And SCAN in LDlist. And lastly, Make Catalog in LDAO. But note that before running Make Catalog, you should first go into the VEC. In the (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | K'NeX Hubs Available for LEdit
|
|
I have built 3 of the standard K'NeX hubs in LEdit. (360, 180 & 90 degrees) If you would like a zipped up copy of these, email me @ Khgudger@cs.com I know that most of you do not want non-standard parts posted to lugnet.cad.dev, but if there is (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: ERROR in lcad9903 update
|
|
(...) OK, I am uploading corrected versions of the complete.exe and lcad9903 update files to both servers as I write this. The "quick fix" mentioned in the first posting will also remain there for the time being. -- Terry K -- (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) Once again, Joshua's argument is sound. So, any other good name suggestions? -- Terry K -- (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | ERROR in lcad9903 update
|
|
Sorry folks, I made a mistake in update 9903. Piece 2429, the 1x2 hinge plate, was overwritten by another part. For an immediate fix, you can download and install this quick fix; (URL) it just like any other update. It contains: 146.dat a ~Moved to (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part 2429
|
|
(...) Joshua's simple typo, but my QA error. I coulda swore I went through all the potential number changes and checked each one for conflicts with existing pieces. Now that the real story is known, I will endeavor to correct the problem ASAP. -- (...) (25 years ago, 20-May-99, to lugnet.cad.dev, lugnet.off-topic.fun)
|
| |
| | Re: Voting Comments
|
|
Steve Bliss skrev i meddelandet <3741a8a1.20817582@l...et.com>... (...) Is that safe for transparent pieces? I toyed a little with re-sorting some parts to 'outside-in' instead of 'inside-out' to make the drawing faster (minimize overdraw), but then (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Spheres in LDLite [DAT]
|
|
I just noticed that when I view a sphere in LDLite in a front, side, or top view, half of the edge line is not drawn. This is true in standard or wireframe mode. In LDraw they are all drawn. I did a little investigation, and it appears to be related (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
