 | | Re: Voting Page
|
|
(...) fixed. (...) i concur.. i never could nail down *what* was causing this to happen.. i just would bring up LDLite during the modeling process and suddenly my type 5's were turned into quads (type 4)... so i'd fix them all manually, grimace and (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page
|
|
Steve Bliss <blisses@worldnet.att.net> wrote in message news:3741a938.209688...net.com... (...) some (...) fix (...) everyone.. (...) Inlining primitives with type 5 lines works fine. But at least sometimes inlining a subpart has turned the type 5 (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
Is there already a button for this? It had odd results when I tried it long ago IIRC. -John Van Steve Bliss <blisses@worldnet.att.net> wrote in message news:3741a8a1.208175...net.com... (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page
|
|
(...) Hmm. I don't remember hearing about this problem before. Probably did, and it fell out of my brain. I will look into the LDAO/inline code, and see what's up. Steve (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) I've thought about writing a function in LDAO to sort a DAT file by line-type: first the 2 (edges) and 5 (conditionals), then the 1 (may be edges, surfaces, or both) then the 3 (triangles) and 4 (quads). Steve (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part Name Question
|
|
(...) I like Bar or support. Those, IMO, are the most-likely non-space use of it. (...) Will the 1x1 end of it use capitalization? (i.e. STUD.DAT) Also, a problem that I noticed with John's mock-up is that the end cylinder was *not* the same (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Part Name Question
|
|
I'm finalizing the "Star Wars Ion Cannon" part, and neither John nor I can think of a decent name for it. Heck, what *category* should it be in? John has suggested one of the following categories: Bar Support Space And I've got the following (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) Speaking as the author of this part, I like the idea of using the word "Bogie" in the description. But also I would like to express in the name that you normally clip this part on the side of the train motor. So I would prefer the following (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) Either of these is fine with me. (...) The 'without corners' name follows the precedent of existing LDraw pieces: 2450.DAT Plate 3 x 3 without Corner 2419.DAT Plate 3 x 6 without Corners 6106.DAT Plate 6 x 6 without Corner 2401.DAT Plate 10 x (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) You can minimize the jagged appearance by using a 1-8cyli.dat around the hole. This leaves the minimum amount of surface around the holes to be jagged in POV-Ray. And if you rotate all the primitives to center your 1-8cyli parts on the (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
