 | | Re: Space Craters Baseplate? [DAT]
|
|
(...) Here it is. Three files: The first is the plate the proper studs. The second is the outline of the mountain in blue. The third is a combination of the first and second. ---...---CUT HERE---...--- 0 Baseplate 32 x 32 with Space Mountains 0 (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | RE: Voting Page
|
|
"Lars" says: ---...--- 290.DAT: Technic Shock Absorber Large, Lower Half (...) Shouldn't these be line type 5 ? (...) Shouldn't the color be 16? (Problem is several places in file) 2909.DAT: Technic Shock Absorber Large, Upper Half Here are also (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) The back of the head in the subpart does indeed use a 2-4cyli primitive. You have a good point, but I am concerned about the two slices of cone-like quads which form the curves above and below the cylindrical face area (on the front of the (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) Good observations, all. (...) Ah ha! A question I can answer! I asked Tore the same question, and he assured me the part is indeed studless. As shown. -- Terry K -- (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Voting Comments [DAT]
|
|
(...) It took me a while, but here are my comments on the current batch of voting parts. Since others have looked closely at the patterned baseplates, I ignored those. 2851: This may be getting a bit picky for this part, but where the peg holes meet (...) (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | ldraw.org dat file
|
|
on the ldraw.org main page there is an images with a wireframe watermarked model... where can i get the .dat file??? (25 years ago, 18-May-99, to lugnet.cad.dev)
|
| |
| | Re: how long is this part?
|
|
(...) There's also one with "Ski," the arctic ThrowBot (or is that ...?) LFB. (25 years ago, 18-May-99, to lugnet.general, lugnet.cad.dev)
|
| |
| | Re: Un-Official Part: Technic Connector with Axle Hole
|
|
(...) I originally thought that the 2853, the axle #2 with offset crank, should have the axle oriented in the X-direction, as do all axles in LDraw, and that the 2854 should have the axle hole oriented in the X-direction, as do almost all parts in (...) (25 years ago, 17-May-99, to lugnet.cad.dev)
|
| |
| | LDAO bug (was Re: Interim update 9903 released)
|
|
There is a small bug in the 'stealth release' of LDAO, which I posted to GeoCities (instead of the LDAO homepage/site). This bug will be noticeable if you install a parts update, but don't immediately run a makelist. When you open the VEC window, (...) (25 years ago, 17-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page
|
|
jonathan's other questions were addressed, but there was one point that was missed: (...) Excuse me, I think you forgot a "please" in this request. Terry puts a lot of time and hard work into the parts updates, and he doesn't need to be badgered (...) (25 years ago, 17-May-99, to lugnet.cad.dev)
|
