 | | 2867.dat Curved 9V Track - reddy —Ludo Soete
|
| | | Hi, Here's the promessed 9V curved track. It's a bit earlier than announced a few days ago, i could work sunday the whole day on it. I hope you like it, and that there arent too many errors in it. If any errors found, let me know, so that i can make (...) (22 years ago, 16-Apr-03, to lugnet.cad.dat.parts)
|
| | | |
| | | | | Re: 2867.dat Curved 9V Track - ready —Tore Eriksson
|
| | | | | Great! Many thanks for the enormous work you have laid down in this part. /Tore Eriksson (without 'c') (...) Ah, nothing to mention. :o) (...) (22 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | | Re: 2867.dat Curved 9V Track - ready —Ludo Soete
|
| | | | | | (...) <SNIP> (...) Perhaps not for you, but without this little piece of software wouldn't i be able to create this part. It was just THIS that make me believe that i could create this part. I'm not a mathematic gouru, and trust me, i'm going to (...) (22 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| | | | | | |
| | | | | Re: 2867.dat Curved 9V Track - reddy —Steve Bliss
|
| | | | (...) Very nice! Good work on this. :) However (I always seem to have a 'however' ;), I'm not sure about your choice of the zero-point and the orientation of the part. The point you chose was very logical, but it might not be practical. In relation (...) (22 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: 2867.dat Curved 9V Track - reddy —Ludo Soete
|
| | | | | (...) That's your right ! (...) The center of the track circle is at: Z=800 (...) O.K. i check it out. When reddy, i'll notify you, and can send you the file for checking - so that i don't upload it too many times on LUGNET. (...) (22 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | Re: 2867.dat Curved 9V Track - reddy —Tore Eriksson
|
| | | | | (...) I think it is incomplete. If I understand your suggustion correctly, that would only work in one curve direction, left or (exclusive or) right. Also, the curved single-rails 3229a, 3229b, and 3230a are not aligned that way. I think a better (...) (22 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | Re: 2867.dat Curved 9V Track - reddy —Ludo Soete
|
| | | | (...) <SNIP> (...) Hi Steve, I just made a quarter curved track using the new 2867.dat file. It works pretty good as it is now. I placed first a straight track, then added a curved one. After only a few moves, the curved track was positioned where (...) (22 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: 2867.dat Curved 9V Track - reddy —Niels Karsdorp
|
| | | | (...) 9V curve part. I just did a quick test using the mpd posted by Ludo and added the filename to PluginTrackParts.ini for the curve in the 9V section and the parts were placed as I expected. Now I don't have to make an update to my plug-in, any (...) (22 years ago, 22-Apr-03, to lugnet.cad.dat.parts)
|
| | | | |
