 | | Re: Need part number for a dangerous predator —Fredrik Glöckner
|
| | | (...) I think it is quite correct of you to add the edge lines where there is sharp corners in the actual part. The ones you did look correctly done to me. If you feel brave, you could also try to add conditional edge lines along the cat, but I (...) (24 years ago, 26-Feb-01, to lugnet.cad.dat.parts)
|
| | | |
| | | | | Re: Need part number for a dangerous predator —Lee Gaiteri
|
| | | | (...) Thanks. I hadn't considered conditional edge lines before (this being my first part, it never crossed my mind; I'm still fairly new to Ldraw and MLcad), but I liked the idea of putting them in. Here's the file with edge lines. I didn't do this (...) (24 years ago, 27-Feb-01, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: Need part number for a dangerous predator —Fredrik Glöckner
|
| | | | (...) Thanks! The cat looks much better with the conditional edge lines. (...) That's a good idea for a LDraw tool! I generally find that edge lines are fairly difficult to handle, so I reckon other people will enjoy the idea as well. Fredrik (24 years ago, 27-Feb-01, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: Need part number for a dangerous predator —Lee Gaiteri
|
| | | | (...) I've done a little more work on the edger, and in the process I've discovered it's a *dandy* integrity checker. Edges that don't match up to just two shapes tend to leave one edge dangling; this helped me find an unnecessary triangle in the (...) (24 years ago, 28-Feb-01, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: Need part number for a dangerous predator —Larry Pieniazek
|
| | | | | (...) <snip> With a handle like LummoxJR and a very refreshing laziness (write a Really Useful Tool to avoid hard drudge work), you must be a RAH fan. I haven't seen a showier "first part" in a while. Now if cats were just available in really large (...) (24 years ago, 28-Feb-01, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | Re: Need part number for a dangerous predator —John VanZwieten
|
| | | | "Lee Gaiteri" <LummoxJR@aol.com> wrote in message news:G9G8nL.GL8@lugnet.com... (...) discovered (...) shapes (...) triangle in (...) This could be of huge benefit to parts authors. Manually adding conditional lines on complex surfaces has to be (...) (24 years ago, 28-Feb-01, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Need part number for a dangerous predator —Lee Gaiteri
|
| | | | (...) Indeed. The task was way too daunting for me with all the triangles and quadrilaterals that were in place. (...) This is the sort of case that exists in my cat. On the bottom, back edge of the stud hole, there's a slight raised section in the (...) (24 years ago, 1-Mar-01, to lugnet.cad.dat.parts)
|
| | | | |
| | | | | | Re: Need part number for a dangerous predator —John VanZwieten
|
| | | | | "Lee Gaiteri" <LummoxJR@aol.com> wrote in message news:G9I0FC.Jr5@lugnet.com... (...) But once your cat is rotated in a model, the line may no longer be vertical. The rounding errors occur at the rendering stage, not the part creation stage. This (...) (24 years ago, 1-Mar-01, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | Re: Need part number for a dangerous predator —Steve Bliss
|
| | | | In lugnet.cad.dat.parts, Lee Gaiteri wrote: [earlier, John VanZwieten wrote:] (...) Remember, there's no such thing as a completely vertical line in 3D modeling. As soon as someone views the kitten from any viewpoint other than straight-on (...) (24 years ago, 1-Mar-01, to lugnet.cad.dat.parts)
|
| | | | |
