Subject:
|
Re: Technic Flex-System Hose (Example MPD file)
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Thu, 4 May 2000 17:02:24 GMT
|
Viewed:
|
742 times
|
| |
|
|
Looks good. Your description/instructions is fine.
Ditto for the ribbed hose part/subparts.
Steve
In lugnet.cad.dat.parts, Fredrik Glöckner wrote:
> Here's an example file featuring a Technic Flex-System Hose at 120 LDU
> length. See lugnet.cad.dev for a reference.
>
> The file names and descriptions are open for changes, obviously. The
> latter especially applies due to my bad English.
>
> Fredrik
>
>
> 0 FILE HOSE120U.DAT
> 0 Technic Flex-System Hose 120LDU Long (open file for usage guide)
> 0 Name: HOSE120U.DAT
> 0 Author: Fredrik Glöckner
> 0 Un-Official Element
>
> 0 A Technic Flex-System Hose is typically seen curved in a model. In
> 0 those cases, some part of the ends are normally fixed inside another
> 0 element, while the rest of the hose is bent. The parts "HOSEEND.DAT"
> 0 are meant to model the straight parts of the hose ends. To achieve
> 0 this, scale them to have the correct length (ie. 20LDU if they are
> 0 fixed inside a unit length connector) and place them at the end
> 0 points. The parts "HOSESEG.DAT" are meant to model the rest of the
> 0 hose. If the rest of the hose is curved, you would typically scale
> 0 the "HOSESEG.DAT" to a have a short length, eg. 4LDU, and use many of
> 0 them along the path of the curved hose.
>
> 0 In the example below, the end points are scaled to 20LDU length, while
> 0 the centre part of the hose is scaled to have 80LDU length, thus
> 0 filling out the rest of the hose.
>
> 1 16 -40 1 0 0 -20 0 1 0 0 0 0 1 HOSEEND.DAT
> 1 16 40 1 0 0 -80 0 1 0 0 0 0 1 HOSESEG.DAT
> 1 16 40 1 0 0 20 0 1 0 0 0 0 -1 HOSEEND.DAT
> 0
>
>
> 0 FILE HOSEEND.DAT
> 0 Technic Flex-System Hose with One End Closed
> 0 Name: HOSEEND.DAT
> 0 Author: Fredrik Glöckner
> 0 Un-Official Element
>
> 1 16 0 0 0 2 0 0 0 1 0 0 0 2 4-4CYLI.DAT
> 1 16 0 0 0 4 0 0 0 1 0 0 0 4 4-4CYLI.DAT
> 1 16 0 1 0 4 0 0 0 1 0 0 0 4 4-4EDGE.DAT
> 1 16 0 1 0 2 0 0 0 1 0 0 0 2 4-4EDGE.DAT
> 1 16 0 1 0 2 0 0 0 1 0 0 0 2 RING1.DAT
> 0
>
>
> 0 FILE HOSESEG.DAT
> 0 Technic Flex-System Hose Segment Open Ended
> 0 Name: HOSESEG.DAT
> 0 Author: Fredrik Glöckner
> 0 Un-Official Element
>
> 1 16 0 0 0 2 0 0 0 1 0 0 0 2 4-4CYLI.DAT
> 1 16 0 0 0 4 0 0 0 1 0 0 0 4 4-4CYLI.DAT
> 0
|
|
Message has 1 Reply:
Message is in Reply To:
 | | Technic Flex-System Hose (Example MPD file) [DAT]
|
| Here's an example file featuring a Technic Flex-System Hose at 120 LDU length. See lugnet.cad.dev for a reference. The file names and descriptions are open for changes, obviously. The latter especially applies due to my bad English. Fredrik 0 FILE (...) (25 years ago, 2-May-00, to lugnet.cad.dat.parts)
|
10 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
