 | | 16L sailmast *30219.dat* [DAT]
|
|
seen in arctic set 6579 original code modified from franklin cain's part 0 Bar 16L with Hollow Studs, Towball, and Slit 0 Name: 30219.dat 0 Original Author: Franklin W. Cain 0 Author: Thomas Burger 0 KEYWORDS Arctic, Xtreme Team, Xtreme Stunts, (...) (20 years ago, 31-May-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Question about creating Cone 4 x 4 x 3 for LDraw
|
|
(...) I don't really want a part rotated 45 degrees from direction it's going to be placed. The Ldraw 'A' command works in 90 degree angles. That's why I chose the orientation I did for the mockup. Plus it matches the other cones. I'd say leave the (...) (20 years ago, 31-May-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Onion Dome (part 44511) from Orient Expedition sets
|
|
In lugnet.cad.dat.parts, William Howard wrote: (snip) I wanted to close the loop on this.. William is right, and I was incorrect about the cross section. I agree that there is no recurve in the part, and thus no figure 8 cross sections when put back (...) (20 years ago, 31-May-04, to lugnet.cad.dat.parts)
|
| |
| | Plant Brick 1 x 1 Round with 3 Bamboo Leaves
|
|
Has anyone modelled this part: (URL) it does not seem hard, but I do not have the skills to make it. Just use the 1x1 brick round and model the leaves once and use them three times? :-) Jaco (20 years ago, 30-May-04, to lugnet.cad.dat.parts)
|
| |
| | Question about creating Cone 4 x 4 x 3 for LDraw
|
|
(...) I happened to get me a seccond hand trainset 725, including two of these cones. So I have started on creating this part for LDraw. By looking at the orientation of the stud and the inner details it seems that this part was creating 45 degrees (...) (20 years ago, 30-May-04, to lugnet.cad.dat.parts)
|
| |
| | Re: "Minifig Fire Helmet Breathing Hose"(x171)
|
|
(...) I am sorry to tell you that this part is currently not appear in MLCAD or LDRAW, you might try to use other parts to replace just as that avitor goggles (20 years ago, 30-May-04, to lugnet.cad.dat.parts)
|
| |
| | Re: 10129 Rebel Snowspeeder
|
|
(...) Orion, Are either of the wedge parts you mentioned available, either officially or unofficially? Thanks. -Joel (20 years ago, 29-May-04, to lugnet.cad.dat.models.sets, lugnet.cad.dat.parts)
|
| |
| | "Minifig Fire Helmet Breathing Hose"(x171)
|
|
Hi. Does anyone have a LDRAW DATA of below parts? ; (URL) I'm trying to model my special task force "BrickHound" on MLCAD, so I need above part-data to make them actable through the night. ; (URL) you would have/know unofficial data of this part, (...) (20 years ago, 29-May-04, to lugnet.cad.dat.parts)
|
| |
| | high res bushlocks?
|
|
I think that the bushlock primitves should be updated to align with the 48 segment primitves. What do others think? (20 years ago, 28-May-04, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: LDraw Part Request - Goblet Fill
|
|
In lugnet.cad.dev, Mark Chittenden wrote: --snip-- (...) Ahh, that's perfect! Just what I needed, thanks. :) Nothing too detailed and overdone, just makes it look like people aren't drinking from empty glasses. :) Thanks a ton for helping. If (...) (20 years ago, 26-May-04, to lugnet.cad.dev, lugnet.cad.dat.parts, FTX)
|
