| | Re: New Part: x744.dat - Technic Gear 42 Tooth
|
|
The problem is I can't confirm postings with long lines while using webmail instead of the pop server I currently am unable to access. I uploaded a better version at: (URL) problem is that when using BFC primitives, they often "disappear" for me in (...) (23 years ago, 20-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 3867 Baseplate 16 x 16 with Island Pattern
|
|
(...) Yes that's it, but my version is that the water is alreddy hardcoded with blue and the baseplate is gray. What version is better? CU Bernd (23 years ago, 20-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Part numbers
|
|
Hi all, I have found at a 30117 - 'Panel 10 x 10 x 2&1/3 Quarter Saucer Top' the number 30320 (it's a transp. light green one). So my question is what about this two diffrent numbers on the same part and are there other parts with different numbers? (...) (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x744.dat - Technic Gear 42 Tooth
|
|
Thanks Tore (...) and I was wondering if the file may have got corupted? I can post the error message if that would be helpful. Best Regards Chris (23 years ago, 20-Mar-02, to lugnet.cad.dat.parts)
|
|
| | 3867 Baseplate 16 x 16 with Island Pattern [DAT]
|
|
I decided to try to create a patterned piece that was missing for ldraw, so here is the island baseplate seen in a couple of Pirate sets. This is my first try at making a part, so let me know if I'm doing something terribly wrong. Andy 0 Baseplate (...) (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 2618.dat Auqanaut Bubble Base (Updated)
|
|
(...) Generally, parts should be modelled right side up -- ie, in the orientation you would expect to see them in lego building instructions. With studs-up. For parts that don't have an obvious "upright" sense, your best bet is to look at other, (...) (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 2618.dat Aquanaut Bubble Base (Updated, Again)
|
|
(...) Look at an inverted slope brick file (like, ummm, (URL)) to see how the problem is solved using the p-files stud2a.dat and 2-4cyls.dat. stud2a.dat is the same as stud2.dat, except there are no edgelines around the base of the stud. 2-4cyls.dat (...) (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x744.dat - Technic Gear 42 Tooth
|
|
(...) (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x744.dat - Technic Gear 42 Tooth
|
|
Tore, Thanks now I don't have any excuse not to finish my clock ;-) Also could you please post 1-4ring9.dat that you used? Thanks in advance Chris (23 years ago, 19-Mar-02, to lugnet.cad.dat.parts)
|
|
| | 2618.dat Aquanaut Bubble Base (Updated, Again) [DAT]
|
|
One question: The hollow studs on the outside rim couldn't be modeled with primitives above a certain level. Therefore if you look at them with LDView you see a smooth cylindar for the top and a 16 sided cylindar for the rest, due to primitve (...) (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|