 | | Re: Would some one model these parts??
|
|
Austin, Since you haven't received any answers, and I think this is the third time you posted this or a nearly similar message in this forum (or one of the other CAD groups), it is probably safe to say that no one has modeled these yet, and also no (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) OK. I'll stick with my statement: the comment should only supply information about *placement*, not provide helpful suggestions about rotating the parts. Steve (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4 [DAT]
|
|
(...) Sorry, my mistake. I think someone suggested the change, and I must have taken it for an official decision. I have no idea who suggeted the name change, only that I didn't like it then, and I don't like it now. My 33062 looks like this: 0 (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Addendum: This "default" is also the usual manner in which LegoCo illustrated their Pirates minifigs who wore this hat: no plume, and centered. In fact several were illustrated as wearing this hat with no plume and *reversed* (180 degrees). (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Yes. I like to have my minifig pirates with their plumes to their left (i.e., "sinister", to borrow a term from heraldry), but someone else (who might be a member of the insidious right-handed conspiracy ;-) might want his minifig pirates to (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | New Part: 3437.dat- Duplo Brick 2 x 2 [DAT]
|
|
Here's my Duplo 2x2- I'd love some feedback. Note that the internal ribbing is quite different from the way that the Duplo 2x4 is done. You also need the primitive referenced here: (URL) your copy of this primitive as stud8.dat. That is likely the (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Updated (again) Part: 3011.dat - Duplo Brick 2 x 4 & discussion [DAT]
|
|
(...) I too have stud5.dat as the Scala stud. As I further cleaned up the 2x2 and 2x4, something else jumped out at me that I hadn't seen before because the part was further off in other areas. Tore's top stud looked good to me at first, but then as (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Would some one model these parts??
|
|
*Can* or *has* some one modeled these parts: (These are parts from the new 2001 set: set # 8241; Battle Cars) 1.) 32146 Tyre Medium hard (*has: 30 4x14 printed on it*) 2.) 32527 Technic panel #5 3.) 32528 Technic panel #6 (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Actually, is there any reason (other than guidelines developed based on symmetry) to orient the hat so the feather hole is in front? I'd say, rotate the part file 120 degrees, and just put in a comment about placement of the feather. Let the (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) I hope that 'someone' wasn't me! (...) In my clean, no local modifications installation of the LDraw Parts Library, the scala stud file is stud5.dat. (...) Yep, I almost posted that those needed to be done, but then I realized that they could (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
