 | | New Part: 3437.dat- Duplo Brick 2 x 2 [DAT]
|
|
Here's my Duplo 2x2- I'd love some feedback. Note that the internal ribbing is quite different from the way that the Duplo 2x4 is done. You also need the primitive referenced here: (URL) your copy of this primitive as stud8.dat. That is likely the (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Updated (again) Part: 3011.dat - Duplo Brick 2 x 4 & discussion [DAT]
|
|
(...) I too have stud5.dat as the Scala stud. As I further cleaned up the 2x2 and 2x4, something else jumped out at me that I hadn't seen before because the part was further off in other areas. Tore's top stud looked good to me at first, but then as (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Would some one model these parts??
|
|
*Can* or *has* some one modeled these parts: (These are parts from the new 2001 set: set # 8241; Battle Cars) 1.) 32146 Tyre Medium hard (*has: 30 4x14 printed on it*) 2.) 32527 Technic panel #5 3.) 32528 Technic panel #6 (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Actually, is there any reason (other than guidelines developed based on symmetry) to orient the hat so the feather hole is in front? I'd say, rotate the part file 120 degrees, and just put in a comment about placement of the feather. Let the (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) I hope that 'someone' wasn't me! (...) In my clean, no local modifications installation of the LDraw Parts Library, the scala stud file is stud5.dat. (...) Yep, I almost posted that those needed to be done, but then I realized that they could (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) I originally thought that the numbers were based on the Lego numbers, but my (admittedly brief) research told me that they didn't, as I found no matches out of about 6 pieces. I realize that parts will often change numbers (how many System 2x4 (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner" [DAT]
|
|
(...) OK, Steve, how about this? If this is OK, LMK, and I'll email you this updated version. ;-) Thanks, Franklin 0 Minifig Hat Tri-Corner 0 Name: x475.dat 0 Author: Franklin W. Cain <fwcain@yahoo.com> 0 Unofficial Element 0 0 CATEGORY Minifig (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Or, at least, replace the paragraph of comments with something like: 0 To put a feather on the hat, use the following line: 0 1 15 0 -10 -12 1 0 0 0 1 0 0 0 1 XXXXa.dat The suggestions about using subfiles are accurate, but it's not (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) Strange. I named the Scala stud to Stud5.dat, but someone renamed it to StudSc.dat. So I thought StudDu*.dat would follow that new pattern... Please note that there are solid Duplo studs on some Duplo baseplates, even though the most common (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4 [DAT]
|
|
(...) To find the correct part number, take a DUPLO 2x4 and examine the underside. There should be a 4 or 5 digit number stamped into the part, usually on the underside of the top. This is the part number. (...) standard. The next available number (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
