| | Rubber Black (was: New Part - 30187 Minifig Motorcycle with 3 Wheels Body)
|
|
This is a separate reply, because this stuff needed to be XFUT lugnet.cad.dev. (...) Or we (that's an inclusive we, not just Paul, Steve and Franklin) should make a decision on what we want to do with "rubber black". There's definitely precedent for (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
|
| | Re: New Part - 30187 Minifig Motorcycle with 3 Wheels Body
|
|
(...) It's the only *current* category that makes sense. We may need to switch over to a generic "Vehicle" category at sometime. (...) I kinda like Tricycle. It *might* be confused with the DUPLO Tricycle, but I doubt it. (...) I'm thinking so, too. (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) Ok, I will fix it and get it re-posted as an updated part. Thank you very much for your input. Paul (URL) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | pirate's head scarf... well... *sort of*... :-P [DAT]
|
|
OK, this is a really, *really* crude mock-up, I'll be the first to admit, but I really needed something that I could use for this piece, no matter how ugly, as long as it looked *something* like the piece in question, plus there's been one or two (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) The open end (i.e., the muzzle) should be pointed in the "negative-Z" direction (i.e., pointing "out" of the screen towards the viewer) when shown in a "front" view in MLCAD/L3Lab/[etc.]). Thanks, Franklin (Who has been thinking of creating a (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - x518 Cannon Pirate
|
|
(...) I will use "Minifig Accessory" as Steve recommended. (...) ok. (...) The cannons I have are the one piece design with the crossed cannon symbol on them. I can do the logo, but it will not look very good rendered. I tried to use as many POV (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) If it doesn't matter much to anyone, I will rename these parts as Steve stated a few messages back; 2527.DAT Minifig Cannon 2 x 4 Base x518.DAT Minifig Cannon 2 x 8 Non-Shooting ( I measured it, end to end) I will categorize both parts as (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) Hi Franklin, When you say to re-orient this part, do I need to point the open end of the barrel to the z+ or z- ? (for clarification) Also, I believe you said to also re-orient the base as well. I will turn it to match the cannon. Let me know (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 30187 Minifig Motorcycle with 3 Wheels Body
|
|
(...) Thanks! They were a challenge. Especially to get all the parts to fit together. When I dis-assembled the base and the body, the base distorted slightly, and I had to find another assembled bike. (...) ok. (...) It was the only one that made (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - 30189 Minifig Motorcycle with 3 Wheels Handlebars
|
|
(...) Hi Bram, Thank you for the comments. I try to use primitives am much as possible to make the best looking POV rendered parts. Paul (...) (24 years ago, 15-Dec-00, to lugnet.cad.dat.parts)
|