| | Re: Un-Official Part: 30358 (SW Landspeeder Engine)
|
|
Karim, I don't have this part in front of me, but IIRC the "fins" are angled, not rounded. Therefor there should be edgelines where the slope of each fin changes (at z=20 and z=-20). Also, I can't tell if there is an edgeline where the box (...) (25 years ago, 8-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [part] Electric Motor 12 Volt
|
|
You've probably noticed this, but there are a couple edge lines sticking up from the back of the part. -John Van Thomas Burger <TBurger666@aol.com> wrote in message news:FCLB40.959@lugnet.com... (...) with (...) to (...) (25 years ago, 8-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [NEWPART]: x738.dat (train) coupling hook (needs work - need help)
|
|
Tore Eriksson <tore.eriksson@mbox3...wipnet.se> wrote in message news:37585322.570431...pnet.se... (...) The curve toward the front is just a 1-8sphe.dat. (...) That would be a torus with inner radius 0 and outer radius 8, correct? There are no (...) (25 years ago, 8-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: Part #30181
|
|
it is used in e.g. the town jr police station and other townjr sets on top of the bay window. (25 years ago, 7-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: Part #30181
|
|
Yes, I have one. It is more of a town jr. part. I got mine in the large RES Q command station(can't remember the real name right now). it could come in handy at some point, but definately falls under the town jr. catagory. Ryan "Build or build not. (...) (25 years ago, 7-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Part #30181
|
|
Has anyone a part that looks like this? I've never seen this part irl, but according to Lego Creator, part #30181 looks like this: (URL) (25 years ago, 7-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [part] mockup/for-post of 30407
|
|
(...) They provided a good challenge to be sure. The two-fingered parts involved lots of trig, while the one fingered part took plenty of trial and error. Modeling the area where the "nubs" on the two fingers slip into the indentions on the (...) (25 years ago, 6-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [NEWPART?] x737.dat Plate 2 x 4 with Hole
|
|
(...) I haven't seen it. The closest thing I can recall would be the 4748, but that is a brick. -- Terry K -- (25 years ago, 5-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [part] mockup/for-post of 30407
|
|
John VanZwieten <john_vanzwieten@msn.com> wrote in message news:FCtvCC.6o8@lugnet.com... (...) posting Oops. Sorry. (...) I just used the one that looked right. BTW, how did you create these parts? They look soooooo good. Beautiful work. (25 years ago, 5-Jun-99, to lugnet.cad.dat.parts)
|
|
| | Re: [part] mockup/for-post of 30407
|
|
(...) Looks good, though I would suggest inlining unofficial subparts when posting parts. Swh1.dat is the correct subpart for this. I wrote swh4.dat specifically for the cockpit, since half the hinge is thinner at one end. -John Van (25 years ago, 5-Jun-99, to lugnet.cad.dat.parts)
|