 | | Re: New Part: Slope Brick 55 1 x 6 x 5
|
|
(...) This is a very old message, but I needed this part and thought it was part of the official parts for a long time... Being indeed part 30249, why is this one still not part of the library? I can see nothing wrong with it, beside it is not BFC (...) (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Straight moving with only one rotation sensor [DAT]
|
|
I' built a similar bot, but the wheels are free-turning. Additionaly, the wheels are pressed down, so that they always have contact to the floor. It's a soccer bot for the RoboCup Junior event. 0 Untitled 0 ROTATION CENTER 0 0 0 1 "Custom" 0 (...) (22 years ago, 13-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Re: Straight moving with only one rotation sensor
|
|
Hello y'all- Does anyone out there know where I can get discontinued lego sets (mainly the autochassis set 8860&65) at reasonable rates here in Ontario? Thanks. (22 years ago, 10-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Straight moving with only one rotation sensor [DAT]
|
|
Hi I saw in the LEGO Mindstorms Web Page that many people made their robots with 2 motors go straight using one rotation sensor on each wheel and stopping the correct motor until both sensors were equal. I got Ultimate Accessory Set as a present (...) (22 years ago, 10-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Re: Problem with click hinge part(s)?
|
|
(...) my click hinges, and the lugs are ALL closer to the top of vertical end wall than the bottom. The position of the lug in your new version is definitely incorrect. Whether thats a problem with the primitive or the sub-part I don't know, but it (...) (22 years ago, 10-Jun-04, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: Problem with click hinge part(s)?
|
|
(...) Actually its the other way about. 30387 is wrong. More accurately, the subpart s/30387s01.dat does not match the guidance notes in p/clh1 and p/clh4. 0 // Placement on side of bricks; rotate accordingly, 0 // place on side 10 Ldu below top (...) (22 years ago, 9-Jun-04, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: New Part: 30299.dat Rock Raiders Canopy base
|
|
(...) The link to the 30298.dat mockup has expired. Do you or anyone you know have a copy of it? (22 years ago, 9-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Part 2495, Minifig Hand Truck
|
|
Has anyone heard anything new about the minifig Hand Truck, part number 2495 (URL) ? Last thing I've noticed is from two years ago, someone said "nope, not yet". I was just seeing if anyone was working on it. It's not in the parts tracker, but that (...) (22 years ago, 7-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: high res bushlocks? [DAT]
|
|
(...) You're probably right. I just remembered that the bushlocks are divided into 32 segments which is fairly colse to 48. Though the notches in bushloc3 would probably align better with the studs if they used the high res primitves at least in (...) (22 years ago, 6-Jun-04, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Problem with click hinge part(s)?
|
|
(...) without measuring, just by sight, I'd say the 1x2 is the incorrect one, it's lugs should be moved up to match the 1x4 ROSCO (22 years ago, 6-Jun-04, to lugnet.cad.dat.parts, FTX)
|
