 | | Train Track Shortcut: 1-2turn.ldr - Train Track 1/2 Circle
|
|
This shortcut needs 1-4turn.ldr, posted at lugnet.cad.dat.models. 0 Train Track 1/2 Circle 0 Name: 1-2turn.ldr 0 Author: Tore Eriksson 1 16 0 0 0 1 0 0 0 1 0 0 0 1 1-4turn.ldr 1 16 0 0 0 0 0 -1 0 1 0 1 0 0 1-4turn.ldr 0 (24 years ago, 19-Apr-03, to lugnet.cad.dat.models)
|
| |
| | Train Track Shortcut: 1-4turn.ldr - Train Track 1/4 Circle [DAT]
|
|
This shortcut can easily be edited for other track or sleeper colours/styles. 0 Train Track 1/4 Circle 0 Name: 1-4turn.ldr 0 Author: Tore Eriksson 1 8 800 -8 0 1 0 0 0 1 0 0 0 1 3034.dat 1 7 735.59 -24 146.32 -0.1951 0 0.9808 0 1 0 0.9808 0 0.1951 (...) (24 years ago, 19-Apr-03, to lugnet.cad.dat.models)
|
| |
| | Re: 2867.dat Curved 9V Track - reddy
|
|
(...) I think it is incomplete. If I understand your suggustion correctly, that would only work in one curve direction, left or (exclusive or) right. Also, the curved single-rails 3229a, 3229b, and 3230a are not aligned that way. I think a better (...) (24 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - reddy
|
|
(...) That's your right ! (...) The center of the track circle is at: Z=800 (...) O.K. i check it out. When reddy, i'll notify you, and can send you the file for checking - so that i don't upload it too many times on LUGNET. (...) (24 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - reddy
|
|
(...) Very nice! Good work on this. :) However (I always seem to have a 'however' ;), I'm not sure about your choice of the zero-point and the orientation of the part. The point you chose was very logical, but it might not be practical. In relation (...) (24 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 9V Curved Track
|
|
(...) The information i have abouth parts center comes from the LDRAW FAQ - Question24 Steve Bliss writes : Quote Tip#1: The Ldraw standard for positioning is to the center of the piece on X=0 and Z=0. Usually, the top of the part (excluding studs) (...) (24 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - ready
|
|
(...) <SNIP> (...) Perhaps not for you, but without this little piece of software wouldn't i be able to create this part. It was just THIS that make me believe that i could create this part. I'm not a mathematic gouru, and trust me, i'm going to (...) (24 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 9V Curved Track
|
|
(...) ... (...) It's the 'normal' part that trips me up! Consider these parts: (URL) a geometry point of view, these are pretty similar. But (according to MLCad) the center of the macaroni is the circle center; the center of the 2x2 'L' is the (...) (24 years ago, 17-Apr-03, to lugnet.trains, lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - ready
|
|
Great! Many thanks for the enormous work you have laid down in this part. /Tore Eriksson (without 'c') (...) Ah, nothing to mention. :o) (...) (24 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | 2867.dat Curved 9V Track - reddy [DAT]
|
|
Hi, Here's the promessed 9V curved track. It's a bit earlier than announced a few days ago, i could work sunday the whole day on it. I hope you like it, and that there arent too many errors in it. If any errors found, let me know, so that i can make (...) (24 years ago, 16-Apr-03, to lugnet.cad.dat.parts)
|
