 | | Re: LPub Q's —Kevin L. Clague
|
| | | (...) Hi Mike, Nice to hear from you! In LPub 4, there is only the orientation file, because you can perform scaling and orientation with one file. Duh! How many years did it take me to figure that out! Hah! Look in the preferences section for the (...) (14 years ago, 13-Sep-10, to lugnet.cad, FTX)
|
| | | |
| | | | | Re: LPub Q's —Mike Walsh
|
| | | | In lugnet.cad, Kevin L. Clague wrote: ... snipped ... (...) I still come up for air every once in a while! ... .snipped ... (...) ... snipped ... I've resolved almost all of the issues I had run into but still have two I am struggling with, (...) (14 years ago, 17-Sep-10, to lugnet.cad, FTX)
|
| | | | |
| | | | | | Re: LPub Q's —Philippe Hurbain
|
| | | | | (...) It doesn't help much, but it appears only on pages with a submodel used twice (x2). Perhaps it would help to see the mpd source file? (...) Right click on the model in the step where you want to reduce scale, choose "Change scale" and choose (...) (14 years ago, 17-Sep-10, to lugnet.cad)
|
| | | | | |
| | | | | | Re: LPub Q's —Kevin L. Clague
|
| | | | In lugnet.cad, Mike Walsh wrote: ... snipped ... (...) Things seem fine through page 14, and then they go away. One of two things come to mind. Either it is an LPub bug, or, possibly the page number is hiding the PLI? I'd make sure that the PLI is (...) (14 years ago, 17-Sep-10, to lugnet.cad, FTX)
|
| | | | |
| | | | | | Re: LPub Q's —Mike Walsh
|
| | | | (...) ... snipped ... (...) I've moved the PLI around thinking it was underneath it but it didn't seem to make a difference. I will send you the MPD file so you can take a look at it. (...) I tried it but even though I told it to apply to only this (...) (14 years ago, 17-Sep-10, to lugnet.cad, FTX)
|
| | | | |
| | | | | | Re: LPub Q's —Kevin L. Clague
|
| | | | (...) I found a bug in LPub. (...) Yes, your highest level model is interesting because the entire model is expressed as steps in submodels, so when it placed the model scale meta, it did it at the top of the step (which is before all the add lines (...) (14 years ago, 19-Sep-10, to lugnet.cad, FTX)
|
| | | | |
| | | | | | Re: LPub Q's —Kevin L. Clague
|
| | | | | In lugnet.cad, Kevin L. Clague wrote: ... snipped ... (...) Another thing that LPub 4 does is automatically center step groups and assembly steps in the center of the page. If there is a single step and with callout(s) on the page, then LPub (...) (14 years ago, 19-Sep-10, to lugnet.cad, FTX)
|
| | | | | |
| | | | | | Re: LPub Q's —Travis Cobbs
|
| | | | (...) It's true that 8.5"x11" (US letter size) is not the same size as metric A4, but the above page includes an entry for QPrinter::Letter, which is exactly 8.5"x11", so unless that's not supported by LPub, I don't think that's the problem. (...) (14 years ago, 21-Sep-10, to lugnet.cad, FTX)
|
| | | | |
