 | | Re: Conditional Ring primitive?
|
|
(...) That's a primitive I have been longing for... but I realized it is impossible to build: where would you put the control lines? The top control points would need to be scaled differently from bottom ones to match various cylinders/cones (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Conditional Ring primitive?
|
|
(...) I just noticed something else while investigating a fix for the above problem. The above model could really use a circular conditional edge primitive. I would vote for x-ycedge.dat as the filename (ie 1-4cedge.dat, 4-4cedge.dat, (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Colinear Vertices
|
|
(...) I played with the settings, and I had to set the precision all the way down to 0.133 in order to get it to fully smooth. (0.125 failed to smooth properly.) (...) .005. I think I'll set the precision to .01, to hopefully give it some leeway. I (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: LETGUI new version 0.1.0.18
|
|
(...) Thanks! For the record: - Ytruder 1.2 is no longer limited to Y direction and can extrude along x, y or z directions - Intersector 1.3 has a new scaling option that improves result for small parts. Philo (16 years ago, 12-Dec-08, to lugnet.cad.dev)
|
| |
| | Re: Colinear Vertices
|
|
(...) It makes sense! (...) An example, this button: (URL) I rounded condlines to 2 decimal places since I couldn't get smoothing anyway. I did more experiments, with full precision in condline it works: (URL) but after rounding to 3 dp there is no (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | LETGUI new version 0.1.0.18
|
|
A new version of LETGUI ((URL) is now available. Support for new commandline options for Ytruder1.2 and Intersector1.3 are added. Have fun! cu mikeheide (16 years ago, 12-Dec-08, to lugnet.cad.dev)
|
| |
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) Welcome back! (...) I agree with Mikeheide, since the total curvature is low I think 6 cones would be more than enough! (...) Seems a good approach. As for the edge line between screw and cones, Isecalc will provide it instantly! (It would be (...) (16 years ago, 12-Dec-08, to lugnet.cad.dat.parts)
|
| |
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) I do not understand correctly what you are saying. If you use a cone primitive you can stretch it in all direction. There is no need to use "about 40 cones". A maximum of 10 should do the same! You should use for this the program "cones and (...) (16 years ago, 12-Dec-08, to lugnet.cad.dat.parts)
|
| |
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) Just to refresh my memory ( I haven't done any parts since 2951) The 48 primitives divide a circle in 48 straight lines, right? That would for a 60 LDU diameter mean that each straight line is approx 4 LDU's long, so using coneshapes each 4 (...) (16 years ago, 11-Dec-08, to lugnet.cad.dat.parts)
|
| |
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) None I know... (...) The official way is to ask a number to a LDraw admin. That said there are numerous parts on tracker named px... (would be px210c01 here) (...) Yes you should be able to use stacked cone primitives. As Travis suggested the (...) (16 years ago, 11-Dec-08, to lugnet.cad.dat.parts)
|
