 | | Re: Lego factory sets / building instructions
|
|
Paul S. D'Urbano wrote: [...] (...) [...] (...) Paul, It would be great if the models were built and commented on. I know the few models that I submitted are buildable, but that kid of defeats the real purpose of Factory... I mean really, if I (...) (18 years ago, 29-Nov-06, to lugnet.trains, lugnet.cad.ldd)
|
| |
| | Has anyone made the x93 Monkey Wrench
|
|
(URL) need it to finish the AT-AT. (18 years ago, 29-Nov-06, to lugnet.cad)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Me too! Kevin (18 years ago, 27-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: Tyre 30.4x14
|
|
ludo soete schrieb: (...) On Peeron this part has the number: 30391. But it is not on the parts tracker. mikeheide (18 years ago, 26-Nov-06, to lugnet.cad.dat.parts)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Hi Kevin, Another possibility to investigate is to change the up vector in inverse proportion to the bezier curve change. That would mean it would twist less where there's a sharper bend, and would possibly end up looking more authentic. But (...) (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Leo, In case you didn't get this far, I solved the above problem and can now control twist all through a cable segment from start point to end point. I calculate the up vector for the start of segment, and the up vector for the end of segment. (...) (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | LDAO problem
|
|
i guess this would be the correct spot for the message. i have a install problem with LDAO. i install it, and when i stat it i get error 76 , path not found. (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | Tyre 30.4x14 VR
|
|
Hi all, Anyone having a mocup from the following tyre? (...) Any help with a mocup is apreciated. Regards, Ludo (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Tyre 30.4x14
|
|
Hi all, Anyone having a mocup from the following tyre? (URL) I noticed the request for it abouth 4 years ago, and it is still not apearing on the LDRAW site - unofficial parts. Any help with a mocup is apreciated. Regards, Ludo (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: DAT file for 4531-9V Switches
|
|
(...) on LDraw's parts tracker searching for 4531. Thanks in advance for any (...) tracking it down. Hi, Take here a look for a mocup of the 9V RC points (100% plastic) by Thomas Burger: (URL) They are build after my mocup for the 9V point (with (...) (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: Lego factory sets / building instructions
|
|
(...) Hi Ville, Unfortunately, there's no simple way to get the typical LEGO instructions experience with Factory. Often LDD's automatic instruction steps aren't well organized and sometimes impossible to follow. It's better if the model author (...) (18 years ago, 25-Nov-06, to lugnet.trains, lugnet.cad.ldd)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
I've got up/side/front vector stuff working now, so that I can control the orientation of cross sections of electrical cables at the start of a segment defined by two constraints. My issue now is that I don't know how to force the twist so that the (...) (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: bend thingie creator.
|
|
(...) Let me check my archive of LDraw related programs and if I have it I'll email it to you. -Orion (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | LSynth electric cable cross section oriention problem
|
|
Hi, I've got a reworked version of LSynth with a major problem... I cannot figure out how to control the twist of the cross section. I use bezier curve to created the nicely curved set of points, and compress it by tossing out points until the angle (...) (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: bend thingie creator.
|
|
(...) Koen, I tried to email you using your address, and I tried to download your bendie thingy creator. It is gone. Does anyone have a copy of this so I can play with it? Kevin (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: Help needed for Train Poster 2006
|
|
(...) i have the cargo train files and the passenger train files here (URL) train parts needed, if not in the same folder can be found (URL) (18 years ago, 24-Nov-06, to lugnet.cad, lugnet.trains)
|
| |
| | parts for german old toy "plasticant"
|
|
When I was a child I played with Lego Bricks and also with the building toy plasticant. Last days my son found the last pieces that I have and my idea was to bring that into LDraw parts. You can found the parts that I already made on my webside (...) (18 years ago, 23-Nov-06, to lugnet.cad, lugnet.cad.dat.parts)
|
| |
| | Re: Help needed for Train Poster 2006
|
|
(...) You can have the 10133 and 10170 from me if you like, as well as the locomotive for the 7898...? And the 10173 has been done almost completely! ;-) Greetz, Anton (18 years ago, 22-Nov-06, to lugnet.cad, lugnet.trains)
|
| |
| | Re: *** Correction: LDView Version 3.1 Released ***
|
|
(FUT lugnet.cad.dev) (...) Actually, all the string handling code for the path stuff is fine (and cross-platform to work in both Windows and *nix). After doing some investigation, I discovered that the problem is that when we do a stat on the (...) (18 years ago, 22-Nov-06, to lugnet.cad, lugnet.cad.dev)
|
| |
| | Re: *** Correction: LDView Version 3.1 Released ***
|
|
(...) This is normally just an extraneous \ No folders normally have them except the root so you need to conditionally add the \. (...) It should look in the LDraw.ini file that gives the correct path. From c:\WINDOWS\ldraw.ini: [LDraw] (...) (18 years ago, 20-Nov-06, to lugnet.cad)
|
