 | | Re: Howto on : BFC "Hold" on 47457.dat
|
|
Given that the part isn't BFC-certified (no BFC comments in the file at all), it by definition cannot contain any BFC errors. For reasons I don't understand, L3Lab is displaying it as if it were BFC-certified. I would suggest pointing out to Steffan (...) (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Howto on : BFC "Hold" on 47457.dat
|
|
I got an e-mail notice that a review of 47457.dat revealed BFC errors. I really don't know how to check for BFC compliance. All I did was to turn the part around to see if any of it was red. I know there's a caveat that some lines bleed red. I (...) (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Problem to synthesize Rubber Tread
|
|
Hi, I have problem to draw a Rubber Tread with MLCad and LSynth, when the process finishes it shows an intermitent Rubber Tread. Please any help will be apreciated (URL) moderation) Gustavo Brinck Lugnet Member 566 Santiago Chile (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) Please understand that I wasn't harping on it to you guys. I had my bit of that, then Steve explained the situation to me (that it's a known problem, that it's being discussed, and that all Wedge Plates will probably end up as Wings), and now (...) (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) Gah! Um, they have been made for LDraw, but those parts have not yet been approved. You can download the requisite files from here: (URL) Right> (URL) Left> Make sure you grab the subfiles and put them all in the right directories or the parts (...) (20 years ago, 31-Oct-04, to lugnet.cad, FTX)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) I downloaded lcad0403.zip and re-ran mklist.exe and sorted by description. Here's a printout of my parts.lst, still no 3x2 wedge plates 41765.DAT Wedge 2 x 6 Double Inverted Left 41764.DAT Wedge 2 x 6 Double Inverted Right 41748.DAT Wedge 2 x (...) (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) That would seem to make sense. They share the characteristics with wing plates of being more-or-less a scalene triangle(1) and coming in both a left and right configuration. Regards, Allan B. (1) Depending on how you classify/measure notched (...) (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) We are aware that this is unsatisfactory, and there is an ongoing effort by the LDraw parts librarians to standardise thse names. Wedge plates will probably all become Wings. Chris (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) They're way at the very end of the Wedge grouping, just before the Wheel grouping starts. They're listed as Wedge Plate 2 x 3 Left/Right. The 2x4 versions are listed as Wings, and the double-wide versions of the same are listed as Wedge 3x4 (...) (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) (quick response, without checking first) Try under Wing. -Tim (20 years ago, 31-Oct-04, to lugnet.cad)
|
