 | | Re: The L PRIZE Pre-Launch: Call for Volunteers, Sponsors, Donations
|
|
I might be going to SIGGRAPH this year. Are you going to be exhibiting at SIGGRAPH or presenting or what? I want to be able to find you there. :) (20 years ago, 30-Jun-04, to lugnet.cad, lugnet.events, lugnet.edu)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) The Type I motor (x564c01) supports both the old style power pickup brick with the plugs at the front (URL) as well as the new style power pickup brick with the plugs at the rear. (URL) The Type II motor (x581c01) supports only the new style (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev, FTX)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) The actual motors (both 12V and 4.5V) were sold seperately as replacement packs, so users can screw open the case and replace the motor (either replacing a broken motor or replace a 4.5V motor with a 12V motor or vice versa). (URL) 12V (peeron (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev, FTX)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) Yes, including case is good. As Niels indicated, the 4 x 12 x 3 1/3 versions are openable with a screwdriver, allowing the actual motors to be replaced, so I think the term "Shortcut" is correct. The 4 x 12 x 4 version is glued, so I'll change (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) I'm confused. Are these parts generally openable - are the actual motors removeable (by the average user)? If they are removeable, then the (shortcut) names should include "case", since they aren't actually the motor. If the motors are not (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
<SNIP> Thanks Niels for taking the time to research this. I have updated the part names based on this information - to remove the voltage designation and correct the dimensions. Regarding your comment "The parts look good, I only miss metal (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: 2nd Civ.Moc entry: Charon - Here's the correct link
|
|
(...) You're right - thanks a lot! The foldernumber-part of the adress had mysteriously dissapeared... The following link should work when the pictures has made it past moderation (if they'll accept pictures of dead minifigs :-) ): (URL) I can't (...) (20 years ago, 29-Jun-04, to lugnet.cad.dat.scenes, FTX)
|
| |
| | Re: *** MLCad V3.10 is available ***
|
|
How does that scan_order thing work? I've added three more paths in mlcad.ini, but the parts in these folders don't show up anywhere in MLCad. [SCAN_ORDER] 1 = SHOW Parts 2 = HIDE Parts\s 3 = HIDE P 4 = HIDE P\48 5 = SHOW NewParts 6 = HIDE (...) (20 years ago, 29-Jun-04, to lugnet.cad, lugnet.cad.mlcad)
|
| |
| | Re: Baseplate 24 x 32 Fire-House with Set 347 Dot Pattern
|
|
(...) Niels There is an image of this baseplate on Brickshelf ((URL) and Steve Bliss and I agreed ((URL) that in this case it would be acceptable to author parts from these images (only the real part photos - not the instruction scans). If you can (...) (20 years ago, 29-Jun-04, to lugnet.cad)
|
| |
| | Baseplate 24 x 32 Fire-House with Set 347 Dot Pattern [DAT]
|
|
When I was building set 347 in LDraw, I noticed that the dots on the baseplate did not correspond with the walls in the instructions. I changed the dots using the instructions. As I don't have this baseplate in real, I don't know how the dots are in (...) (20 years ago, 29-Jun-04, to lugnet.cad)
|
