 | | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) I do apologise if I misinterpreted your words, but I would suggest that my interpretation is an extremely reasonable one given the word choices you used. (...) I would think not, but I look to the steering committee to do a lot more than make (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw, FTX)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) Hi Allister - Thanks for that clarification. Actually, I was at a momentary loss for how to approach the answer, but now after thinking it through I have something to say. I would hope that whoever is elected to the Steering Committee would (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw, FTX)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) I agree. (...) I suggested nothing. I was merely asking a question. Can you just answer it without reading motives into it that don't exist? Is it really necessary to be a member of the steering committee in order for suggestions on the (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw, FTX)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) I concur. :) I haven't been following this thread at all up until now, but Jake's post caught my eye. And I agree with what he said - only I want to go a little further. Couldn't anybody that even has association with TLC possibly have a (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw)
|
| |
| | Conflicts of Interest
|
|
(...) All: While the goal of avoiding conflicts of interest is a laudable one, in practice large numbers of committees operate with members who have them. It is far more important that potential conflicts be disclosed as they crop up. If the (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) I don't see this discussion as about Tim at all, except as a test case. As I've said before, he's a handy metric. Any rule that excludes him (based on his current employment situation) is wrong, and worse, it is in my view bad for the (...) (21 years ago, 4-Feb-04, to lugnet.cad.dev.org.ldraw, FTX)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) I for one certainly don't doubt your devotion to the hobby, nor do I doubt that you will do anything but behave with the utmost integrity as a member of the committee. However, despite this it does concern me that there is nonetheless a (...) (21 years ago, 3-Feb-04, to lugnet.cad.dev.org.ldraw, FTX)
|
| |
| | Re: LDraw.org Bylaws Drafts: Call for Public Discussion and Consensus
|
|
(...) All, I hope you don't mind if I chime in on the discussion. I just caught up on the thread, and there are a lot of very good things being tossed around. Personally, I tend to like the idea of Larry's to exclude any mention of LEGO employee (...) (21 years ago, 3-Feb-04, to lugnet.cad.dev.org.ldraw) !
|
| |
| | Re: TRAIN RIDE
|
|
Thanks for all the suggestions. I am thinking about a tunnel also. The problem is the file size. The colors have to be reduced to keep the size down and the more detail I add the less reduction frame to frame I get. The file right now is 356kb. How (...) (21 years ago, 3-Feb-04, to lugnet.trains, lugnet.cad, lugnet.animation)
|
| |
| | Re: Naming of parts
|
|
(...) In general, a wedge is a 'clipped' brick and a wing is a 'clipped' plate. I don't see any exception to this rule in the official library but if an exception exists on the PT then those part should be commented upon. -Orion (21 years ago, 3-Feb-04, to lugnet.cad.dat.parts)
|
