 | | 3069p02.dat - Tile 1 x 2 with Tape Reels pattern [DAT]
|
|
Here's another one. Please LMKWYT. Thanks. (Tore, Someone requested this part, but gave it a slightly different name. Please use this name for the entry in your parts tracker. Thanks.) Thanks, Franklin 0 Tile 1 x 2 with Tape Reels pattern 0 (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Repost: 973p103.dat Minifig torso with Han Solo (with jacket) pattern [DAT]
|
|
With a better filename. 0 Minifig Torso with Han Solo pattern (with jacket, from set 7190) 0 Name: 973p103.DAT 0 Author: Matt Schild 0 Unofficial part 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 1 1 16 0 0 0 1 0 0 0 1 0 0 0 1 s\973s01.dat (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Follow up to Camera Tricks
|
|
Hi, I was having problems because the PCT value was not set at 0 so the values I inputted for the camera position put the camera in a place I did not expect. Thanks Jay Jacinto (...) if (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: Follow up to Camera Tricks
|
|
OIC Thanks Jay Jacinto (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: Follow up to Camera Tricks
|
|
Think of "angle" as "zoom". The smaller the number, the "closer" you are to the object. The larger the number, the "further away" you are. Royce (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: Follow up to Camera Tricks
|
|
Hi Jay; If you want to adjust the "look at point" you can actually select one of your peices in a model. Look at it's co-oridnates in the Model Part List (top right window). Then put these exact co-ordinates into the "look at" point... You will be (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: 973solo.dat Han solo torso from the Millenium Falcon set
|
|
(...) In the actual movie, if you look closely, he's wearing a shirt whose color I would call "bachelor's white", i.e., it was white maybe when he originally bought it... ;-) (...) _Nice_ job. :-) (Personally, I _hate_ doing asymetrical jobs.) (...) (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: How do I speed things up ?
|
|
(...) I go to this tab and set the "stud mode" to "None". It renders even faster yet. (It can make it a little difficult to work with at times.) If you plan to use Baseplates.... Wait until the end if you can. I try to place little markers for the (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: 4150p101.dat - tile 2 x 2 w/ SW imperial pattern
|
|
(...) There is supposed to be a bit of flaring on these, I admit I put WAY too much, but there is supposed to be some. (...) Since Franklin did a much better job of it than I did, I'm just going to scrap my version in favor of a superior one. (...) (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 4150p101.dat - tile 2 x 2 w/ SW imperial pattern
|
|
(...) I assume you're actually referring to the "P"-numbers (i.e., the numbers _after_ the letter "P", to indicate which pattern is being used). Most of these have been organized (mostly by Chris Dee, the infamous minifig torso designer ;-) to be (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
