 | | Re: 32198 Technic Gear 20 Tooth Bevel
|
|
(...) I was checking it against the part 4143.DAT Technic Gear 14 Tooth Bevel Since this part is the original bevel gear done by James Jessiman, I would say that 6589.DAT has the wrong orientation, since it does not conform to the orientation of the (...) (24 years ago, 30-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 32198 Technic Gear 20 Tooth Bevel
|
|
(...) OK I would change the part, but I do not agree with the rotation of 180deg around Y axis. For me it is correct compared to (URL) However, I noticed that the tooth of all my new parts are incorrect. I will publish an update very soon. Marc (...) (24 years ago, 30-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: "stud" rendering in LEdit?
|
|
All stud*.dat files are handled this way by LEdit. Well, I'm not sure about stud5.dat, but I expect LEdit will recognize that file as well as the basic 4. Steve (...) (24 years ago, 30-May-00, to lugnet.cad.dev)
|
| |
| | Re: new (sub)part - "s\45s01.dat" - Grip Segment (for Katana)
|
|
(...) Yep. It's at the ldraw.org updates page: (URL). Steve (24 years ago, 30-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: [Part] 4515p03.dat - Slope Brick 10 6 x 8 with Slate Roof Patt ern
|
|
(...) Using MLCad 1.7, I get some bleed-through and noise (could be the same things) in both versions. In L3Lab, everything looks good. Steve (24 years ago, 30-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Brickbay Temp URL Available
|
|
You just start LDLite from a command prompt, with a -MS option. MS is for "Mode Save". Something like: c:\ldraw\ldlite\ldlite 3001.dat -MS (assuming LDLite is installed in c:\ldraw\ldlite\) Steve (...) (24 years ago, 30-May-00, to lugnet.market.shopping, lugnet.cad)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) typo typo... yes, I meant to say I can't be on the committee. I guess if I were committed, I'd have lots of time... if I could only convince my therapist to allow LEGO as therapy. (...) take that to off-topic.debate, it's debatable. (...) (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Put me down for a minumum of 100 USD (and like Larry, I'm good for more if it is necessary to get the project off the ground). (...) I know some people say you should be committed Larry, but that's not what we're talking about... Tim just (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) be (...) at. I (...) Ya, right after I pressed fire I realised it was a bit cryptic. Lets try again. What is "at cost"? (we all agree that it makes sense to press 1000 of them because that's where the cost per starts to get cheap) One *could* (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Thanks! (...) I'm not completely undersrtanding... I know that 50 at cost is what they asked me for in an email - could you clarify 1000/1050? I *think* I understand what you're getting to but I'm not 100% sure. Its 5am. -Tim (URL) timcourtne (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
