 | | Re: new program to aid part making: ldraw circle creator
|
|
I have to agree here. Some of your messages are kind of(sometimes very) confusing. And when you reply to a message you delete what was in the message rather than leaving the part of the original message you were replying to. If you were to do that, (...) (28 years ago, 8-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
(...) Could you set your line length to less than 80? The whole sentence above that starts with "I have to" is one huge long line. (28 years ago, 8-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Traffic page link
|
|
Todd, would it be practical to hook up a link to the traffic page near/at the top of the browse lugnet.com/news/groups/groups page? That might make browsing a bit more flexible. -Tom McD. remove the spamcake. (28 years ago, 8-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Lugnet.cad.dat heirarchy
|
|
I agree, and I think cad.dat serves very well for MOC's. -John Van jonathan wilson wrote in message ... (...) (28 years ago, 8-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Incorrect LUGNET Link
|
|
I was browsing through the plan you keep referring to: (URL) page makes reference to the Minifig Generator but points to good old (URL) when it should be (URL) a little time to find that - if I didn't remember baseplate.com I never would have found (...) (28 years ago, 8-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Traffic page link
|
|
(...) Good idea. However, the (URL) page and its subpage (URL) are going extinct soon... so we'll need to find a better place to link to the traffic page from...maybe we can link to it from the new homepage. The /news/groups/ and /news/groups/loc/ (...) (28 years ago, 8-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
I'm sorry but it did not show up like that in email for me. I checked the message on the web and it was in your post that showed up with the line being long, not mine. Ryan ***...*** REPLY SEPARATOR ***...*** (...) (28 years ago, 9-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
Came out long to me as well. .02, John (...) (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Traffic page link
|
|
(...) the (...) browsing (...) Todd, sounds great. Will that include any search capabilities? Date ranges, posters, topics, etc. (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Traffic page link
|
|
(...) Sorry, I meant to say "Will it STILL include....." (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Traffic report bug?
|
|
Why does lugnet.loc.us.tx.aus appear as 8 when only one post was made in the last week? Matt (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Traffic report bug?
|
|
(...) Where do/did you see that? On the traffic report page?-- (URL) column did you see it in and at approximately what date & time? Thanks, --Todd (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
(...) That's probably because your newsreader isn't set to wrap out-going messages or it's line-wrapping is non-standard. The web interface may be able to understand the protocol, but not all other newsreaders do. When the message is replied to, it (...) (28 years ago, 9-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Re: Traffic report bug?
|
|
In column 3 on the traffic report page sometime this morning, maybe a couple of hours ago. I've seen it jump around from 1 to 8 a few times since I posted to that group. > (...) (28 years ago, 9-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
I'll see if I can find a way to change it. I don't read all the groups so I don't see all the things like that that could be helpful. Ryan ***...*** REPLY SEPARATOR ***...*** (...) (28 years ago, 9-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
Ryan, Did you set your margins wide to post to cad.dat and then forget to set them back to 78 characters or so? I noticed you made a bunch of cad.dat posts lately, and I know I've forgotten in the past. -John Van SCOTT R DENNETT wrote in message (...) (28 years ago, 9-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | Re: new program to aid part making: ldraw circle creator
|
|
Um, I don't think that's possible because I haven't figured out how to change line length yet :) I will look into it though. Ryan ***...*** REPLY SEPARATOR ***...*** (...) (28 years ago, 10-Apr-99, to lugnet.admin.general, lugnet.cad.dev)
|
| |
 | | A tiresome tirade (Was: garbage output)
|
|
All, Events in the past few months has led up to the point where several typically cool-headed individuals have blown their tops. All this anger and frustration is aimed at one individual in particular, and is counter-productive. Recent lambasting (...) (28 years ago, 10-Apr-99, to lugnet.cad.dev, lugnet.admin.general)
|
| |
 | | Re: A tiresome tirade (Was: garbage output)
|
|
Sproaticus wrote in message ... (...) typically (...) frustration (...) <snip... very well spoken text> I have been away for awhile and have only now been able to start reading Lugnet again. The recent flames in *.cad were surprising to me. However, (...) (28 years ago, 10-Apr-99, to lugnet.admin.general)
|
| |
 | | Re: Traffic report bug?
|
|
(...) Very odd. If you see it happen again, could you do a file/save of the HTML page and e-mail it to me? --Todd (28 years ago, 10-Apr-99, to lugnet.admin.general)
|