Results 5341 – 5360 of about 16000.
|
Search took 0.00 CPU seconds.
|
|
| |
|  
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
 | | Re: 1/4th stud offsets.......
|
| (...) I'd say your way is pretty good! That's a clever idea, taking half the offset on each side that way. People have also demonstrated 1/5 stud offsets as well, (IIRC Gianluca Morelli did I think), so using these two together it ought to be (...) (22 years ago, 20-May-02, to lugnet.build)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Amazon honor system
|
| (...) I thought they take a pretty significant fee out, to where if someone gives you a buck you don't end up with much at all... (?? could be misremembering) Thus making Paypal better from a net receipt perspective. (22 years ago, 20-May-02, to lugnet.admin.finance)
| |
|
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Powering motors from the mains
|
| (...) Yes. That is what I meant. I even believe sincerely that it's what I said. :-) I am not sure who exactly within LEGO first recommended it but if you dig hard enough in lugnet.robotics I believe you will find just such a recommendation.... that (...) (22 years ago, 18-May-02, to lugnet.technic, lugnet.robotics)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Stickers in LDraw?
|
| (...) one of the pressing (1) questions indeed. This search (URL) this thread: (URL) was very interesting reading but I'n not sure it was definitive. It seemed to spend time on parts certification. Tony's post: (URL) a lot of good issues though... I (...) (22 years ago, 17-May-02, to lugnet.cad.dev)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Powering motors from the mains
|
| In lugnet.technic, Mark Morgan writes:> (...) wanted to power, it is exactly what you need and no extra. Those 4548s turn up in the strangest places, though, so haunting old and poorly managed stores (TRU comes to mind, as Mark said!) that carried (...) (22 years ago, 17-May-02, to lugnet.technic, lugnet.robotics)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Advanced Design Train Roundhouse
|
| (...) I would go 48 if I could. But I should hasten to point out that it is prototypical for engines not to fit on the turntable in US practice. It happened fairly frequently. The most common solution was to service the engine in the stall that was (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Advanced Design Train Roundhouse
|
| (...) it, just the main drive. It's a fairly standard drive with the motor in the house. Another note, Steve's setup is very modular. Although it makes up a fixed configuration (that spans at least a 5x8 foot area when the yard is included), it's (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Advanced Design Train Roundhouse
|
| (...) Steve Ringe, our 8 Wide King. I will see if I can get him to reply, he usually is too busy building to post much. (...) The turntable sequences by using mindstorms touch sensors to detect when the table is "close" to the approach track and (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Powering motors from the mains
|
| (...) Purist approach is to use a 9V train speed reg and LEGO(r) wires from the speed reg to your motor(s), possibly through the polarity reverser switch to give control. The speed reg is powered from a wall wart trafo so if you buy a UK train set (...) (22 years ago, 17-May-02, to lugnet.technic, lugnet.robotics)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: George Lucas: Galactic gasbag
|
| (...) AND all the articles it references. All thought provoking. Thought the David Brin one was especially good as it got to the heart of something that's bothered me about SW (and something I'd liked about ST, imperfect as ST was) all along. (...) (22 years ago, 17-May-02, to lugnet.off-topic.debate)
| |
|
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Hi, I'm a newbie, blah blah blah
|
| (...) I perceive that as bait. I feel I was trying to be helpful in my answer because your post seemed to indicate that you were unclear on how to manipulate news by mail subscriptions. I choose not to rise to it further. (22 years ago, 17-May-02, to lugnet.people.newbie)
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: Hi, I'm a newbie, blah blah blah
|
| (...) Try going here and seeing what you are subscribed to (assuming you are getting these posts sent via email, if not, I'm confused) (URL) if you are subscribed to people.newbie, remove it. If you're NOT, and you're getting email nonetheless, try (...) (22 years ago, 17-May-02, to lugnet.people.newbie)
| |
|
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
| |
|
pieniazek
(score: 0.248)
|
|
| | Re: pictures at tracker
|
| (...) not*"building*, no... but *make*-ing is quite feasible since it would be incremental and unless the upload was a major major basic primitive, not of huge effect, right? I am thinking that you run make as a background job from cron every 2 min (...) (22 years ago, 16-May-02, to lugnet.cad)
| |
|
pieniazek
(score: 0.248)
|
More: Next Page >>
|
