 | | Light grey and Dark grey colors in POV Ray?
|
|
What colors are used for light grey and dark grey in POV Ray? I rendered some models yestreday and the light grey color I used in MLCAD turned dark grey and the dark grey color turned blue. I'd appreciate some help before I start rendering more (...) (25 years ago, 23-Sep-99, to lugnet.cad)
|
| |
| | OVER 1 AMP
|
|
Now, I recieved two good answers for my problems. 1) Built an H-Bridge 2) Use the LMD18200 Now has any one any documentation on an easy H bridge that I could build without wasting much time? The same goes for the LMD18200, I understand that is not (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Availability of Orange Bricks at Legoland California?
|
|
(...) Well, I'm not a Carlsbad AFOL, but I was there last week(1), and saw nothing resembling an orange bucket. James (URL) soon! (25 years ago, 23-Sep-99, to lugnet.general)
|
| |
| | Re: before I reinvent the wheel
|
|
No, but I have used my HP48sx to control the Fascinating Electronics board as well as an NRD535 shortwave receiver. The serial I/O of the HP48 is limited to shield, ground, tx and rx pins so in both cases I had to wire special cables to jumper (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Source for IS1U60
|
|
Hi Igor - - When you need to locate parts, try this link: (URL) found a couple of sources for the IS1U60 through them. - Nick - (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Space stations?
|
|
Duane: (...) Why not both kinds. I don't think we need to define any standards for "fly-in" docks, but a CDP standard would be useful. I am thinking of something with an opening of 80 LU by 160 LU (roughly three minifigs tall), but an intermediate (...) (25 years ago, 23-Sep-99, to lugnet.space)
|
| |
| | Re: Source for IS1U60
|
|
(...) Addendum to my last post. For my money, I would get the LiteOn unit instead. Its less fragile (nifty metal can) and has the same pinout as the Sharp GP1U58Y units, and you can get them in a variety of frequencies at (URL) Part Number 160-1153, (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Standardized Inventory File Format?
|
|
Steve Bliss wrote in message <37ea300b.59491442@l...et.com>... (...) People may end up with multiple commas if there happens to be a gap of six or more spaces, then. Of course after replacing ' ' with ',', they could replace ',,' with ','. It might (...) (25 years ago, 23-Sep-99, to lugnet.db.inv)
|
| |
| | Re: Source for IS1U60
|
|
(...) (URL) carries them, but they currently say they have no stock, you'd have to find what their lead-time is. Also, a Canadian firm (URL) carries them, and they DO have them in stock. HVW's cost about US$1.00 more, but at least you can get them! (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | (canceled)
|
|
|
| |
| | Re: Space stations?
|
|
(...) I haven't built a fully working model yet, but have played with the mating slopes on either side of the door. I found that to get a good mate between the two sides, the female portion must be one plate taller than the male. In doing so, the (...) (25 years ago, 23-Sep-99, to lugnet.space)
|
| |
| | Re: Standardized Inventory File Format?
|
|
(...) Look at (URL) The LDraw numbers are included there, and there are links to Technica and Lutz Uhlman's parts list. Steve (25 years ago, 23-Sep-99, to lugnet.db.inv)
|
| |
| | Re: Standardized Inventory File Format?
|
|
(...) Are there many programs that support multi-character delimiters in their import function? I'm fairly certain Excel and MS-Access do not. The point of making a standard format is to make the data more accessible to everyone. Not just coders. I (...) (25 years ago, 23-Sep-99, to lugnet.db.inv)
|
| |
| | Re: Chrome in new LCAD programs
|
|
(...) Have you looked at the LDLite extended meta-statements? Among other things, they allow colors to be defined and redefined in models. I'd recommend supporting these commands -- for some of them (probably the rotate, translate, and transform (...) (25 years ago, 23-Sep-99, to lugnet.cad.dev)
|
| |
| | Re: Watch those prices (and those cashiers too)
|
|
3 cheers for effective customer satisfaction. I'm sure that the additional money you saved on the sets will be easily recouped by the store from your continued and increased patronage. It's interesting because over the past few years there have been (...) (25 years ago, 23-Sep-99, to lugnet.market.shopping)
|
| |
| | Re: Lets get a datsville castle going
|
|
(...) That's a nice idea in theory, but in order to do that, we need LOTS and LOTS of structures, unless each town is only 5 houses or something. I take it you're planning to duplicate structures to fill up space? If not, it'll take a long time.... (...) (25 years ago, 23-Sep-99, to lugnet.castle, lugnet.cad)
|
| |
| | FT: Castle Sets - 1974, 6062, 6054, 6060, 6039, 6018, 6081, 6071
|
|
I recently picked up some castle sets as part of a collection I bought. Since I am not a castle person, I would like to trade these for Train or Town sets. At this time these sets are not for sale. Please see my list of wanted sets at: (URL) as (...) (25 years ago, 23-Sep-99, to lugnet.market.buy-sell-trade)
|
| |
| | Re: New pics of the finished commuter train
|
|
Seems to be working now, just visited it. Larry, your right, it is AWESOME. Good job Steve!! I think I'll take a break from my scenery projects and work on some trains. Tom (...) (25 years ago, 23-Sep-99, to lugnet.trains)
|
| |
| | Re: gone fishin
|
|
(...) All the standard colors are in the LDraw FAQ. Now, if someone wants to research RGB values for some of the newer colors, that'd be very cool. STeve (25 years ago, 23-Sep-99, to lugnet.cad.dat.models, lugnet.cad.dev)
|
| |
| | Re: G'Day!
|
|
Damn! Two people from Sydney! I'm from the Southern Highlands myself, though I work in Sydney. So what's your pleasure gentlemen - town, space, technic? You'll find my site rather self explanatory - Guards and pirates have been my weakness. Richard (...) (25 years ago, 23-Sep-99, to lugnet.loc.au.nsw.syd)
|
