 | | Re: The Blue, now the New Green!
|
|
(...) Wow! The new green works really well, allowing the creations to stand out against the background, despite its obvious brightness and interest. It's remarkable how the overall effect of same creations, in the same pose, can appear to change (...) (17 years ago, 5-Feb-08, to lugnet.publish, FTX)
|
| |
| | Re: The Blue, now the New Green!
|
|
In lugnet.publish, Eric Sophie wrote: The Blue (URL) for Mecha-Tech 2048x1360>> (URL) Blue ESLC 2008©> Now the New Green! (URL) for Mecha-Tech 2048x1360>> (URL) Green ESLC 2008©> Enjoy! (URL) Eric Sophie> (17 years ago, 5-Feb-08, to lugnet.publish, FTX)
|
| |
| | New Trains-n-Town website.
|
|
Hey folks, Many of you know that I setup and have run the Save 9V Trains site for some time. Well the usefulness of that site has come to an end. Being the insane LEGO fan that I am I just had to do something else. To that end I have set up a new (...) (17 years ago, 5-Feb-08, to lugnet.trains, lugnet.town) !!
|
| |
| | Re: Base plate thickness?
|
|
(...) Thanks, Scott. That's very helpful. I've got to get me some calipers! Rafe (17 years ago, 5-Feb-08, to lugnet.general)
|
| |
| | Re: Which CAD program recommended for Mac??
|
|
(...) Moving things manually a long distance is cumbersome, even with the coarse grid. The inspector does show the coordinates of the selected part or submodel, although I'm not sure if that's what you mean by cursor coordinates. Note that if you do (...) (17 years ago, 5-Feb-08, to lugnet.cad, lugnet.cad.dev.mac)
|
| |
| | Re: Base plate thickness?
|
|
(...) 0.055 inch would be correct. It never crossed my mind that 0.5 = 1/2. I don't use my calipers often enough to correctly interpret its output every time I do. Lesson learned: Double, uh, no, triple-check the readout (and make shure I'm (...) (17 years ago, 5-Feb-08, to lugnet.general)
|
| |
| | Re: Which CAD program recommended for Mac??
|
|
(...) Yes, this is very annoying as using the arrow keys to move a part/assembly all the way across the model can be slow and painful, especially since Bricksmith doesn't seem to display cursor coordinates. (...) Ok, I see. I'd like functionality to (...) (17 years ago, 4-Feb-08, to lugnet.cad, lugnet.cad.dev.mac)
|
| |
| | Re: Base plate thickness?
|
|
(...) Scott, I'm sorry; That can't be right. More than half an inch? Did you mean 0.055 inch? I'm talking about the thickness of a baseplate, the area without the studs, the distance a block would be above my desk if the block were sitting on a (...) (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) rats! (...) Thanks for the heads up, John Looks like I really have to start brushing up on my NXT 'bot building now. Dave K (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Base plate thickness?
|
|
(...) 0.55 inch. That's measuring with a dial calipers. HTH sjf (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) Dick Swan's replacement RCX firmware also does not support directly manipulating the IR led and it doesn't support microsecond timing control. Both of these features would be required in order to send the IR messages to a Power Function or R/C (...) (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Base plate thickness?
|
|
(...) Baseplates are exactly the right thickness, such that if they are resting on studs, their studs are exactly 1 plate higher. So I guess that makes them 1 plate minus the height of a stud 8?) ROSCO (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | light bley cheese
|
|
Yay! (URL) of 'em. Now if only I had any inspiration to build anything . . . Still in a funk, Jonathan (17 years ago, 4-Feb-08, to lugnet.inv)
|
| |
| | Base plate thickness?
|
|
Hi all, I have this hankering to know the thickness of a baseplate. Not a regular plate, but a baseplate. I found the FAQ page with dimensions of bricks and plates and studs ( www.lugnet.com/~330/...dimensions ) but cannot seem to find out how thick (...) (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
In lugnet.general, Jason J Railton wrote: <snip> (...) I'm runnign Dick Swan's alternate firmware that he sent me a while back. Dave K (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Hi and test of service
|
|
(...) Hey and welcome! God Bless, Nathan (17 years ago, 4-Feb-08, to lugnet.people.newbie)
|
| |
| | mondo senza confini
|
|
tramite bricklink ho appena comprato un po' di lego da un negozio....in NUOVA ZELANDA ! La cosa curiosa e' che questo venditore abita a circa 800 km dal mio punto antipodale (gearth mi ha aiutato :-) e' realmente dall'altra parte del mondo ! Bravo (...) (17 years ago, 4-Feb-08, to lugnet.org.it)
|
| |
| | Re: Si resta qui
|
|
ciao a tutti anche per me è da tre giorni che non ricevo più le mail di conferma. Adesso sto scrivendo dal Web. Riguardo al nuovo forum, come già dicevo, non sono contrario a crearne uno alternativo, magari di riserva se si blocca ancora questo. (...) (17 years ago, 4-Feb-08, to lugnet.org.it.itlug)
|
| |
| | Hi and test of service
|
|
I've been a member for a while, but I've never said hi. So, I'm saying hi. Scott (17 years ago, 4-Feb-08, to lugnet.people.newbie)
|
| |
| | Re: Which CAD program recommended for Mac??
|
|
(...) Bricksmith is certainly unlike MLCad, which is indeed a fine program. However, I'd like to humbly correct a few inaccuracies I perceive in your list of drawbacks. (...) True. That is a definite difference. (...) False. Keyboard controls for (...) (17 years ago, 4-Feb-08, to lugnet.cad, lugnet.cad.dev.mac)
|
