 | | Re: [rtlToronto] rtlToronto20 Draft Rules Posted
|
|
(...) Hi Guys, I have three questions. First it says that the becon light is on when the robot is stopped? Does that mean the it can't be on while the robot is moving around or what? Or is it that it can only go on when another robots has stopped it (...) (20 years ago, 22-Nov-05, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: T3 Board colors & rules
|
|
(...) No need to do that. My prototype sits completely behind the board. It doesn't extend along either side of the board. Speaking of which, I finished up the controls last night. I've just got a little bracing I'd like to do then it is on to (...) (20 years ago, 22-Nov-05, to lugnet.org.us.laflrc)
|
| |
| | Tidningsartikel om mitt lego
|
|
Hej allihopa. Nu äntligen har jag kommit med i lokaltidningen.Det blev en ganska stor artikel med en fin översiktsbild av tåget.Här kommer en länk (URL) Hoppas ni gillar det ni läser dock är det en del fel som jag pratat med inblandade om.Ha det så (...) (20 years ago, 22-Nov-05, to lugnet.loc.se, FTX)
|
| |
| | Re: Random Pneumatic idea/question
|
|
(...) Yes, I was wondering what method should be used to bleed them successfully. The clamp idea is a good one. My compressor is very basic. I don't have buggy motors. To build the pressure/vac engine all you would have to do, I assume, is split the (...) (20 years ago, 22-Nov-05, to lugnet.technic)
|
| |
| | Re: Random Pneumatic idea/question
|
|
(...) You will undoubtedly have to bleed the air out of the system when you put in your hydraulic fluid. Otherwise the system won't perform as well. (...) Kev (20 years ago, 22-Nov-05, to lugnet.technic)
|
| |
| | Re: Random Pneumatic idea/question
|
|
(...) Hi Billy, Well, my recollection of a composite five port switch was faulty. When I tried to create a two piston timing circuit (precursor to motor), it would leak because all four switches would be on, letting pressure directly through to (...) (20 years ago, 22-Nov-05, to lugnet.technic)
|
| |
| | System to allow pressure and vacuum for piston at the same time
|
|
Hi, Single LEGO pneumatic switches are not capable of controlling a pneumatic system that uses both pressure and vacuum to drive a given cylinder at the same time. A single switch does not let you capture the exhaust inherint when a piston contracts (...) (20 years ago, 22-Nov-05, to lugnet.technic, lugnet.robotics, lugnet.announce.moc) !
|
| |
| | How's LEGO Factory working out?
|
|
I got trapped under something heavy and haven't followed things in the LEGO world for the last couple of months. Last I was in it, a few of us had just figured out how the LEGO Factory bags are organized, and how to get part sets into LDD that (...) (20 years ago, 22-Nov-05, to lugnet.cad, FTX)
|
| |
| | Re: Legofest di Crema
|
|
io ci sarò solo la domenica. porto un piccolo e semplice modulo GBC giallo, ma che ha mi richiesto mesi di preparazione... porterò anche l'855 così da poter fare la storia delle "crane technic" se qualcuno porta le altre! ciao ciao, luca (...) (20 years ago, 22-Nov-05, to lugnet.org.it.itlug)
|
| |
| | Re: Striscione ITLUG
|
|
bello! se possibile, io farei la scritta molto più grossa, diciamo delle proporzioni di quello dei francesi di freelug. ciao, luca (...) (20 years ago, 22-Nov-05, to lugnet.org.it.itlug)
|
