 | | Finally the Wait is over...
|
|
Looks like Book 5: Order of the Phoenix is going to be released in the early Summer... June 21st to be exact. It is going to be a best-seller....already (even as it is being announced). It is over 255,000 words ... and EVEN larger than HP: Goblet of (...) (22 years ago, 19-Jan-03, to lugnet.harrypotter)
|
| |
| | Re: A space workhorse MOC from Port Block Yards
|
|
On 02:33 01/19/2003 +0000, Richard Parsons wrote (...) Nice little design. Reminds me of a sub meets a transfer truck :-) Nice, simple SNOT effects and a clean design. Would make a nice series of shots/short stories about working class ships at a (...) (22 years ago, 19-Jan-03, to lugnet.loc.au, lugnet.space)
|
| |
| | A space workhorse MOC from Port Block Yards
|
|
Morning all, Port Block Yards has released pictures of the Chifley Class Yard Support Vessels. (URL) bound to find a few of these around any Port Block Yards shipyards, and you may even encounter them on their own, going about the business of the (...) (22 years ago, 19-Jan-03, to lugnet.loc.au, lugnet.space)
|
| |
| | Re: Help with construction detail
|
|
(...) Try this: (URL) a 1x5 Technic Rotor 2 Blade with 4 Studs. Joe Meno (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Space.
|
|
(...) Shweet.. I'm waiting for the wall poster with Neil Brickstrong's autograph. -Tom McD. (22 years ago, 19-Jan-03, to lugnet.space)
|
| |
| | webbed dish and rod/bar
|
|
I've tried to find the webbed radar dish and any rod/bar in 3 colors and can't i found blue dish and blue rods i found red dish and red rods orange dish, no rods yellow rods, no dish etc can anyone tell me if there is a third color that has the dish (...) (22 years ago, 19-Jan-03, to lugnet.general, lugnet.space)
|
| |
| | Re: Sensor Sampling; Progress?
|
|
The Lego firmware cuts power for about 200uS, with a period of 3mS. So most sensors have to have enough capacitor based power storage for the full 200uS and be able to run on about 93% duty cycle. (The rotation sensor is one of the devices on the (...) (22 years ago, 19-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with construction detail
|
|
In lugnet.castle, Tanya K. Burkhart writes: ... (...) ... Hi. I'd recommend using a rubber band. I've had good success using rubber bands between motors and gear assemblies, and I can't see why it wouldn't work here. A long rubber band would allow (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Help with construction detail
|
|
(...) I've linked one of those to an axle before; I used the 1x5 hinge system to do it. In effect you end up with something that looks an awful lot like a helicopter rotor, with the short bar 3 fingers one end/2 fingers at right angle on the other (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Help with construction detail
|
|
(...) First off, there don't sem to be any sort of larger technic axles to facilitate the use of these rotors other than the red 'seated' axles in the kit itself. I would prefer you use this part instead. (URL) can be used in conjunction with normal (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
