 | | webbed dish and rod/bar
|
|
I've tried to find the webbed radar dish and any rod/bar in 3 colors and can't i found blue dish and blue rods i found red dish and red rods orange dish, no rods yellow rods, no dish etc can anyone tell me if there is a third color that has the dish (...) (22 years ago, 19-Jan-03, to lugnet.general, lugnet.space)
|
| |
| | Re: Sensor Sampling; Progress?
|
|
The Lego firmware cuts power for about 200uS, with a period of 3mS. So most sensors have to have enough capacitor based power storage for the full 200uS and be able to run on about 93% duty cycle. (The rotation sensor is one of the devices on the (...) (22 years ago, 19-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with construction detail
|
|
In lugnet.castle, Tanya K. Burkhart writes: ... (...) ... Hi. I'd recommend using a rubber band. I've had good success using rubber bands between motors and gear assemblies, and I can't see why it wouldn't work here. A long rubber band would allow (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Help with construction detail
|
|
(...) I've linked one of those to an axle before; I used the 1x5 hinge system to do it. In effect you end up with something that looks an awful lot like a helicopter rotor, with the short bar 3 fingers one end/2 fingers at right angle on the other (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Help with construction detail
|
|
(...) First off, there don't sem to be any sort of larger technic axles to facilitate the use of these rotors other than the red 'seated' axles in the kit itself. I would prefer you use this part instead. (URL) can be used in conjunction with normal (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: roll call (27 more needed?)
|
|
(...) And the module factor is basically infinitely expansible, depending on how you set it up. (...) Using the dithered colours isn't that bad, but drawing off the harry potter sets, I guess that's the only possibility, eh? I've still yet to (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Sensor Sampling; Progress?
|
|
(...) Yes. (...) individually (...) That's right. (...) I agree. With the current firmware, power gets cut off to all 3 sensors for ~85us (sometimes longer). With the scheme I mentioned, power would be cut to only one sensor for ~25us. The sample (...) (22 years ago, 19-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Sensor Sampling; Progress?
|
|
(...) What OS are you using? How far have you got? Max. (22 years ago, 19-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: roll call (27 more needed?)
|
|
(...) A combination - or it will be. That's the plan, anyway. The entire "basement" (the level where the moat would be if I had more space to spread out) is a very solid structure, but the towers and buildings will have spaces that open. I'm (...) (22 years ago, 19-Jan-03, to lugnet.castle)
|
| |
| | Re: Nose doors?
|
|
(...) Not opening. However, on my Via F unit, it has 2 1x4 tiles on the nose to simulate the door. Problems I can see are that they opened outwards, and are only ~1 stud wide or at most 2. (most had a 2 part door). Hinging would be a problem using (...) (22 years ago, 19-Jan-03, to lugnet.trains)
|
