 | | Re: questions on optical encoders
|
|
On Sat, 18 Apr 1998, Paul wrote: Might I suggest taking a look at US Digital's optical encoders? (URL) have some low cost variants that we used and were very pleased with. I am looking at the data sheet for a "SP-16" <snip> (...) It is 1.78" in (...) (26 years ago, 18-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | questions on optical encoders
|
|
Hi, everyone Hi, i am currently doing a thesis topic "Micromouse project". And, I am going to purchase an small optical encoder to measure the speed, acceleration and distance that my mice has taken. My mice is driven by a DC motor, so the opti. (...) (26 years ago, 18-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: polaroid sonar problems
|
|
Hi all if anyone has problems using the 6500 series for distances below 35cm by using the binh signal I have a possible solution to the problem. We also expierienced problems using the sensors for distances between 15cm and 40cm. We finally found (...) (26 years ago, 17-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | ds1233
|
|
Help: I am short one ds1233 for my freshman engineering class. Is there anyway to jumper around this part. I understand that it is in the circuit to prevent the cpu from losing it's mind on low voltage. I would be willing to put up with reloading (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | polaroid sonar problems
|
|
We continue to progress on our first robot here at Northwestern but have run into a problem with our sonars. We have run out of solutions to try and would appreciate any help from people experienced with the polaroid sonar modules. Our sonar is (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Writing in port D of the Handy Board
|
|
Hello, We've just read the Web page "Additional Digital Inputs & Outputs for the Handy or Finger Board" at (URL) we don't know how to write in the port D (ie D0..7 ) in order to have more digital outputs. Please could you tell us how to do ??? (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Using Port D of the Handy Board
|
|
In your message you said: (...) ve just read on the Handy Board FAQ that it was not possible. So, where is the truth ??? where in the FAQ does it say that it's NOT possible? If you look at the link (URL) explains how to use Port D as outputs. (...) (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Using Port D of the Handy Board
|
|
Hello everybody, A few month ago, someone told us that we can use port D as an ouput. But, we've just read on the Handy Board FAQ that it was not possible. So, where is the truth ??? Help, help, help !!!!!!! We need 8 ouputs (and also 8 inputs) to (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard Buffalo V1.0 - Update
|
|
Hello again, Fred G. Martin had informed me that I forgot the assembly code for the Buffalo monitor. It is now on the page, (URL) BUF_HB.TXT Charles Hacker School of Engineering Griffith University - Gold Coast PMB 50 Gold Coast Mail Centre (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard Buffalo V1.0
|
|
Hello All, Some time back I sent a message to the HandyBoard list to enquire if anyone had a machine code programming monitor operating system for the HandyBoard, similar to the Buffalo Monitor on Motorolla's EVB boards. (The Buffalo system allows (...) (26 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
|
