| | reset vector
|
|
Hi, I am trying to run a basic assembled .asm file on the handy-board without IC. Since the board doesn't have a reset button, do I use the power on reset (turning board off/on) vector location of $FFFF:$FFFF to indicate the start of my code? -Luke (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Polaroid Sonar
|
|
Recently got my OEM kit from Polaroid Corp. In the readme file which i ftped from cherupakha.media.mit...trib/kent, it says "for robust operation solder a 0.01uF cap to C7 of the ranging board." I browsed through the schematic and component layout (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: HELP!
|
|
when using DLM, does the downloader make it to the second stage of the download, indicating "synchronized"? also, when attempting to download "config0c.s19," do you give DLM the command line flag indicating to burn EEPROM and not RAM? you must tell (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re[2]: expansion board
|
|
Actually I wanted an analogue signal giving some idea of distance. I've done it with a 555 oscillator for illumination, and an opamp demodulator circuit. I was thinking that this might be useful on the expansion board. Richard ___...___ Reply (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: downloading
|
|
(...) Did you run the strip_cr utility on the .S19 file to make the file's lines end correctly? * Michael L. Ross/C33 | Lockheed Martin Eng & Sci Svcs Co. **** * Robotics Department | 2400 Nasa Rd. 1, Houston, TX 77058***** * (281)333-7094; (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | HELP!
|
|
I hope that someone reading this can please help me with a problem that I am finding difficult to solve. I have completed section 4.3 "Micropro and Oscilaator cct" and confirmed that the oscillator is running. However after section 4.4 "Serial line (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | problems downloading own .asm
|
|
Look at the .s19 file, and see if it's downloading anything between 0 and FF. (You should be able to stare at your .s19 file and the pcode for a while and figure out the 4 hex bytes which contain the address for a line). Downloading something to the (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: Motors & handyboard
|
|
(...) What is 20? (...) Current meters have an internal resistance. The lower the current range the larger the resistance --- even with digital current meters. Some typical values For example: Digital Analogue Current Range R_meter R_meter 200 uA (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | downloading
|
|
HI, I cannot get any .s19 file except for pcode_hb.s19 to download to the handy-board. This downloads and when I run IC it all works fine. The .s19 file I would like to download is just a normal .asm file assembled with as11.exe. I am just putting (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Compiling (interactive) C programs
|
|
Hi all, Some time ago I found a link somewhere on the handyboard page. This link referred to to someone who made a interactive C compiler for Unix environment. I would really like a compiler for the handyboard instead of the the C interpreter.(for (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | DC Motors....
|
|
Does anybody know where I might get replacement motors, more suitable to the B, for the Tamiya Bulldozer Kit??? HELP!! These motors are not suitable, but the tank unit is nice. The motors are stable, but draw to much current. Also, the speed of the (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
|
| | downloading
|
|
HI, I cannot get any .s19 file except for pcode_hb.s19 to download to the handy-board. This downloads and when I run IC it all works fine. The .s19 file I would like to download is just a normal .asm file assembled with as11.exe. I am just putting (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: MEMORY FAULT
|
|
This problem is answered in the Handy Board FAQ. You are loading the wrong s19 file. -Fred -- This message was composed using Articulate Systems' PowerSecretary, a Macintosh-based speech-to-text dictation system. Please forgive any sloppiness in the (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
|
| | program for handyboard
|
|
I have started to assemble a handyboard and was wondering if there is a program that will allow the handyboard to simulate a walk through of a maze on my monitor or somthing similar of this type????? (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: expansion board
|
|
I too have used a similar technique. I used a 555 timer and a 567 tone decoder instead of a PIC. Using an IR can from Rat Shack, and five ir-LED's I get a sensor that sees straight ahead, 30 degrees and 60 degrees to each side. Set the 555 for about (...) (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|
|
| | IR LED's
|
|
Hi Bill, Are you able to transmit IR beams through more than one LED (eventhough the handy board has only one LED driver port). If this is part of your IC code, could u please mail it to the net. Thanks Sriram (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|
|
| | SPI Routines in IC
|
|
Anybody have any routines or know of any published information for using the SPI with IC for: ...use with Dallas Semi's serial real time clock - DS1202 ...use with 12 Bit serial A/D - LT1298 ...use with Dallas semi's Thermomerter - DS1620 Thanks a (...) (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: Motors & handyboard
|
|
(...) 3v toy motors are noisy little buggers and were never designed to be anywhere near a microprocessor. if you reduced the hb motor battery supply to 3v, you might have a chance. at 9v, i really doubt it. -f (...) (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Motors, gear boxes, tools
|
|
Greetings: on the Hanyboard web page, Tower Hobbies is mentioned as source for RC supplies etc. I would reccommend highly for electric motors, gear boxes, tools including a nice metal turning lathe, Hobby Lobby International www.hobby-lobby.com (...) (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: Motors & handyboard
|
|
To measure current with an multimeter or ammeter (volt/ohm/etc.. meter) you must break the circuit at some point and put the meter in series with the circuit thus gapping the break. ie) +-----(+) METER (-)------+ | | | | (+) | POWER | (-) | | | | | (...) (28 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
|