|
|
 | | Re: ir communication
|
| Yes there is. It is LNP it is availiable for windows or linux. I am just fiddling with the windows version see: (URL) I did not get it working just fine see also my post just before you (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | ir communication
|
| Hi, i am just doing my first steps with legOS and i want to send some data back to the PC. Is there any kind of software for the PC to read that data and save or display it? TIA Chris (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | WINLNP QUESTIONS
|
| Dear all, I have some troubles setting up WinLNP. I am new to RCX (2 months) and legOS (1 month) and have not much experience with VC6. I want to set up a line of communication between PC and RCX. I downloaded everything from (URL) and I managed to (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | Re: transfer data failed
|
| (...) One other thing, did you erase the firmware from the RCX before trying to load legOS? regards Frank Caggiano "The best education for the best caggiano@crystal-objects.com is the best education for all." (URL) Robert M. Hutchins Logo Users (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | Re: transfer data failed
|
| (...) Did you try slow? (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | Re: transfer data failed
|
| (...) Did you try using the slow mode option ("-s" for firmdl3) as was suggested? (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | Re: transfer data failed
|
| Hi, thanks for the tips, but nothing helps. I tried 0.2.5, I tried the far and near mode, I changed the lighting conditions -> nothing helped. But I don't think that I fired up my Brick/Tower because the original Lego Software under Windows works, (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| | | | | Re: As promised - Mecha using RCX with MacNQC - Draft 1.
|
| I think you're off to a good start! You mention some problems that I think can be overcome, others I'm not sure about... but I'll offer my two cents anyway... (...) a) what's your gear reduction ratio? I see a worm gear in there, which is about the (...) (23 years ago, 11-Aug-01, to lugnet.build.mecha, lugnet.loc.au, lugnet.robotics.rcx)
| | | | | Re: As promised - Mecha using RCX with MacNQC - Draft 1.
|
| (...) I like the design, but as with most RCX-based walkers, it looks, well, 'clunky'. I realize this can't be helped considering the nature of what it is you are working with. I, too, have been working on a walker of this nature and have met with (...) (23 years ago, 11-Aug-01, to lugnet.build.mecha, lugnet.loc.au, lugnet.robotics.rcx)
| | | | | As promised - Mecha using RCX with MacNQC - Draft 1.
|
| Hi, well some weeks ago I promised that I'd begin a project of developing a Mech incorporating the RCX unit, some motors and sensors. Here is my very first attempt at a minifig scale Mech: (URL) RCX is programmed using MacNQC and at this stage only (...) (23 years ago, 11-Aug-01, to lugnet.build.mecha, lugnet.loc.au, lugnet.robotics.rcx)
|
|
