To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.trainsOpen lugnet.trains in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Trains / *9959 (-10)
  Re: Canadian Trains from California?
 
(...) I too have made a lego VIA model (engine only ) (URL) (24 years ago, 27-Jan-01, to lugnet.org.ca.nalug, lugnet.trains)
 
  Re: Lightweight show tables
 
(...) Compression should be minimal unless you manage to create a fairly concentrated force. Using baseplates on top would eliminate most of the possibilities of the LEGO causing localized damage. (...) They look about the same to me. On the other (...) (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: Lightweight show tables
 
(...) Yes, you do need quite a bit of force to break it but it could happen, especially at a show situation. Another issue I ahve with foam is that it could be crushed/compressed making it a poor building surface. (...) dense blue (or was it pink- (...) (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: Lightweight show tables
 
(...) For the curious, I'll wander by the foam plant on Monday, and see if I can grab a spec sheet on Dowboard. I know they measure for torsional stress tolerances, and horizontal shearing strength, and other technical terms. :) James (there are (...) (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: Lightweight show tables
 
(...) I think you have to work pretty hard to break it, though perhaps the 3 layers of 1/2" foam is significantly stronger (there is glue between the layers which might serve to strengthen it somewhat). My tables have had QUITE a bit of abuse and I (...) (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: Lightweight show tables
 
(...) 5/8" is WAY thicker than you need, and particle board is heavier than plywood. The 3/8" that PNLTC specs is probably a good choice, though 1/4" is thick enough also. Frank (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: 'Article from Tommorow' < Warning Speculative!!>
 
(...) Where can I get LDraw ???? Michael Pratt (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: The Limacion track design is BUILT!
 
"Brad Hamilton" <bhamilto1@home.com> wrote in message news:G7spqq.H3E@lugnet.com... (...) Thanks. (...) of (...) I'll admit, I did use some reference from a book titled "The Way Things Work"(I honestly don't know if it's still being published, (...) (24 years ago, 27-Jan-01, to lugnet.build, lugnet.general, lugnet.loc.us.ca.sd, lugnet.org.us.baylug, lugnet.trains)
 
  Re: Lightweight show tables
 
(...) I have built a table similar to the one you describe for my dad's N-scale layout that resides in his living room. I don't think the foam will stand up to the abuse put forth by building with lego on it. It's pretty easy to crack 1" foam by (...) (24 years ago, 27-Jan-01, to lugnet.trains)
 
  Re: Tapping into the Track's electricity
 
"Doug Pegram" <DPegram@worldnet.att.net> wrote in message news:G7twMo.Cu5@lugnet.com... (...) FRED! Flashing Rear End Device. Maybe that's just a Canadian thing, though... I prefer FRED to "EOT". :) Iain (24 years ago, 27-Jan-01, to lugnet.trains)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR