 | | Re: Power Functions infra-red RC protocol released!
|
|
(...) Absolutely excellent news! Downloaded and printing... (17 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
Thank you very much for that fine piece of software Bob! After reading your post I immediately run in my LEGO room to grab an RCX and the IR tower to test your software. Well, I had to find out that I had not enough batteries at home and thus had to (...) (17 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) I did this experiment a while ago, I just presumed everyone else has as well. The Short answer is NO. I could not get the new IR train to control the PF receivers either at full on, or with PWM. My IR train, and PF gear are 100% incompatible. (...) (17 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) Okay, thanks. I can get 'Single output Mode' to work now. 'Single pin Mode' may be working too, but I'm not sure what to expect from it. I would expect setting either C1 or C2 would set them to 9V and run a motor forwards or backwards. Setting (...) (17 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) I'd be very interested in that experiment (using a Hobby train RC on the PW Receiver) as well, but this does answer a number of questions for trains. For instance, tunnels and large layout out of line-of-sight on the RC should now be possible. (...) (17 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) Either single pin modes allow to set each output to 1 (9V) or 0 (0V). (...) See the drive datasheet: (URL) can reach 1A peak, continuous value is lower (500-600mA) especially if both outputs are heavily loaded at the same time. Philo (17 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) Bob, I could not wait to get home from work to try this. I want to say thank you; your effort has saved me many countless hours. I loaded the Firmware, and the Program into a 1.0 RCX, and the brick worked flawlessly! On my 1.0 brick, I was (...) (17 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Norfolk & Western Y6b 2-8-8-2 Steam Locomotive
|
|
(...) Cale: That is one sweet looking loco. :-) I happen to be a fan of the jagged boiler look. It gives it that strong, tough, and rough around the edges look. Very nice. I agree with Tony that 9-wide just sets this thing off. It really puts it in (...) (17 years ago, 26-Jan-08, to lugnet.trains, FTX)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) The toggle bit is checked in Single output mode (the documentation is not quite right for this mode) and in both single pin modes. each message is sent 5 times you need to toggle the toggle bit in every message sent. 0 1 0 1 0 1 0 1 etc. bob (17 years ago, 25-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Norfolk & Western Y6b 2-8-8-2 Steam Locomotive
|
|
(...) Wow. Just... wow. I absolutely love this locomotive. Not just because it looks great, but because the way you've solved some problems I've run into in the past with attaching pilot and rear trucks. I've been drooling over this locomotive now (...) (17 years ago, 25-Jan-08, to lugnet.trains, FTX)
|
