| | Re: DCC chip installed in accessory brick
|
|
(...) I have trouble accepting the destruction of a perfectly good 9V motor so I guess I will not be making many of these. Unless of course I stumble across a few 'dead' motors!! My best 12Volt locos have two motors so the power pick-up bogey has to (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: DCC chip installed in accessory brick
|
|
(...) Sweet! Love to see pics sometime :) Yeah, the 9v train housing is a strange animal, but I'm pretty much used to it now. My biggest qualm is the lack of 'fake middle wheel' expandability for 3 wheel power bogeys to emulate newer NA locos. Right (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: DCC chip installed in accessory brick
|
|
(...) Yes! It works, I came home this evening and cut open a perfectly good brand new 9V motor and put a 1.5 amp decoder inside and connected it to the 2x2 electrical plate on the motor housing. Now I have those old 12V locos running again. They (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: MOC 36 Axle Schnabel Car
|
|
(...) design? (...) Nah, its time for TLC to release that new radius curve they are keeping secret... Rob (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: A couple of new train things
|
|
(...) Thanks Ben ,for the link to the Rolling bricks site. Yes, it's a 7 wide ! It's funny that you replyed to my message . As I have been studying your trains ,and Holger Matthes trains, for a while now. I copied your design for the 7750 style (...) (21 years ago, 26-Nov-03, to lugnet.trains, FTX)
|
|
| | REMINDER: BayLTC at GATS this weekend!
|
|
For Immediate Release Contact: Russell Clark rclark@telis.org 408.605.5412 (cell) Please note, some of the information has been updated. SAN FRANCISCO BAY AREA, CA - The Bay Area LEGO Train Club (BayLTC) is pleased to announce that we have been (...) (21 years ago, 26-Nov-03, to lugnet.loc.us.ca.sac, lugnet.loc.us.ca.sf, lugnet.org.us.baylug, lugnet.org.us.sacbb, lugnet.trains, lugnet.trains.org)
|
|
| | Re: DCC chip installed in accessory brick
|
|
(...) I don't have a 12v motor but this mod should be pretty easy. Good luck with that. As for modifying--for my good friend that asked, here's a walk thru: (URL) K (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: MOC 36 Axle Schnabel Car
|
|
(...) It will go through the straight part of the point but the load catches on the control arm when it tries to take the branch. It will run on a layout if the inside of all curves have the clearance it requires. It is 155 studs long coupler to (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: DCC chip installed in accessory brick
|
|
Now if I can just steel myself enough I will be taking the motor out of a train motor and fitting a HO scale decoder inside with the motor outputs going to the 2x2 connector. I will put this in a train with a modified 12-9V connector cable to a 12V (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
|
| | Re: MOC 36 Axle Schnabel Car
|
|
(...) Maybe its time to switch to a curve, straight, curve, straight, corner design? Josh (21 years ago, 26-Nov-03, to lugnet.trains)
|