 | | Re: legOS
|
|
(...) I tried what you said quite a bit but it just says "usage error: try nqc-help' to display options" My serial port works fine for my Scout Tool program. and I have tried to switch the RCX to the scout like this "nqc -T Scout" and "nqc -TScout" (...) (25 years ago, 13-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: legOS
|
|
(...) nqc -SCOM2 You need to be careful about upper/lower case for options. I know its annoying, but there are a *lot* of options, so case is important. In the case of specifying the serial port, the option is immediately followed by the serial port (...) (25 years ago, 13-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: legOS
|
|
(...) How would you tell NQC to use COM2? like this? NQC -s COM2 or somthing like that? (25 years ago, 12-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: legOS
|
|
(...) "could not open serial port" generally means one of these things: 1) You told NQC to use a serial port that doesn't exist. By default, it will try to use Mac - modem port Win - COM1 Unix - /dev/ttyS0 You can override this with a -S option. 2) (...) (25 years ago, 12-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: legOS
|
|
(...) The scout does NOT have replaceable firmware. What you have is all it will ever be... So it's NQC or nothing at this point. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 11-Feb-01, to lugnet.robotics.scout)
|
| |
| | legOS
|
|
Hi, do any of you think that you can program the scout in legOS? My NQC is not working it says "could not open serial port" and it aborts the download so legOS would mabe work. Alex (25 years ago, 9-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: ScoutTool unable to initialize Ghost
|
|
(...) Hi Have you tried pulling the cable out and pluging it back in? I have had some problems with that and also it does the same thing on my laptop I think the serial port is no verified. do you have a mac or pc? Alex P.S. Oh and make sure the 9V (...) (25 years ago, 9-Feb-01, to lugnet.robotics.scout)
|
| |
| | ScoutTool unable to initialize Ghost
|
|
Why would opening ScoutTool.exe with Windows 95 display "Unable to initialize Ghost" with Scout turned ON and within 10 cm of IR Tower? Already followed procedures under "Init Ghost" in Help (ScoutTool.pdf). Thanks in advance for any help. (25 years ago, 9-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: NQC
|
|
(...) Thanks I figured out how to use it! :) But I still have a problem. every single NQC program from any books or documentaion that i'm sure have been tested, dont work! it just gives me undefined variable messages. The only NQC program that works (...) (25 years ago, 8-Feb-01, to lugnet.robotics.scout)
|
| |
| | Re: NQC
|
|
Alex, In addition to the links that Rainer provided, you could also check out the following: (URL) tutorial, written by Mark Overmars (the author of the Rcx Command Center), introduces NQC and can is usefull even if you're not working with RcxCC. (...) (25 years ago, 8-Feb-01, to lugnet.robotics.scout)
|
