 | | Re: Vision Command on a Mac
|
|
(...) I'm pretty sure it's the same camera that's going to be in the Movie Maker Sets. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC 2.2 r1 released
|
|
NQC 2.2 is finally out of beta test. I appologize for the long alpha/beta cycle...it wasn't that there were tons of problems, but just that I have been quite busy with a lot of other things. There were only a few minor fixes between 2.2 b1 and the (...) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc) !
|
| |
| | Re: Problems with datalog
|
|
(...) Unless I bungled the code, NQC should handle this ok. Old versions of NQC would always move from a restricted datalog source into a temp variable. With the new firmware, there's the added complexity that the temp can't be a local var, and I (...) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Vision Command on a Mac
|
|
(...) The included software is Windows only. I don't know if it could be tricked into working under Virtual PC or not. Just from the physical design of the camera though, I would think Lego must have a Mac version in the works. (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems Solved(WAS Re: Problems with datalog)
|
|
(...) Ya, VC must have gone to press before they asked us to help with the bugs... 0321 was really buggy. I'm glad you got it worked out. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Vision Command on a Mac
|
|
(...) If the mac has pci slots you can install a USB card. this , of course doesnt mean the software will work but you can add USB ports to "some" older macs. I am using a usb/firewire orange micro card in my 7500 power mac ( requires OS 8.6 or (...) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Vision Command on a Mac
|
|
(...) No chance. The camera is USB. (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Vision Command on a Mac
|
|
I there any way of getting this up and running on an old Mac with serial ports ? For months now I have been trying to figure out a way to accomplish what Vision Command does using third party hardware & software but haven't been very successful. Any (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Problems Solved(WAS Re: Problems with datalog)
|
|
(...) before (...) I just tried using the Wait() command for up to 5 seconds. Still didn't work. I remember reading that the Vision Command required the new firmware. I assumed that VC d/l'd the new firmware automatically. I didn't remember waiting (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) Have you tried putting in a Wait command after creating the Datalog and before you start using it? It must take a few milliseconds to set up. Just my .001 cents after taxes... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
