 | | swan firmware motor problem
|
|
Hi, I trying out the Swan firmware (Fast0103.lgo) with nqc 3.1 r4 but for some reason the motors won't turn on. Has anybody seen something like that? If I run the program, it does all the other things, even switch on the little motor triangles on (...) (18 years ago, 9-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RCX remote jammer
|
|
(...) Sorry peoples - the program is working again. Try it out on your unsuspecting friends - watch the channel YOU want to. :) As far as I know, I'm the only one to have figured out how to do this with the RCX, and it's a pretty good joke. Prgm (...) (18 years ago, 23-Jun-06, to lugnet.robotics.rcx, lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Join the Hoodia revolution
|
|
Hoodia 920+ -- The newest and most exciting fat loss product available - As seen on Oprah! (URL) testimonials: "I was originally amazed that the first two pills I took of Hoodia 920+, almost immediately took my cravings away. Now 4 weeks later, 3 (...) (18 years ago, 17-Jun-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-based proximity measurement
|
|
(...) You're welcome - it's a fun problem. At least partially because it's one of the few times I've had to worry about the speed of bytecode execution under the standard firmware (see below). (...) Given what you are transmitting and how you are (...) (18 years ago, 11-Jun-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-based proximity measurement
|
|
Brian, thanks for your advice. it has told me what is happening physically. i build a one shot measurement program to answer your questions. here is the measurement result: Distance to wall: 26 cm (at night) 7740 7696 7666 7641 7639 7613 7613 7593 (...) (18 years ago, 11-Jun-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-based proximity measurement
|
|
(...) Well, there were a couple of typos, but only one I found that was critical. If you are using a "max-picking LIDAR" method, you do *not* want to divide by the number of samples. The variable "eyeon" in your code should end up with the brightest (...) (18 years ago, 9-Jun-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-based proximity measurement
|
|
(...) i have downloaded the SerialPing.nqc program hoping to get an easy to use proximity sensor. i have modified it to work with only one light sensor. but it shows always -90 on the display. ok, sometimes -89 too. can anybody tell me, what i did (...) (18 years ago, 9-Jun-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RCX remote jammer
|
|
(...) I haven't actually used the program in a long time, and I'm getting compiler errors now - I think I've updated BricxCC/NQC since then, and I might have to adjust a few things. At any rate, it shouldn't be far from working, so play around with (...) (18 years ago, 17-Apr-06, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | RCX remote jammer
|
|
this is going to be short, b/c I only have a minute. Check out (URL) (after mod) for an NQC program that will allow you to jam almost any IR remote control signal. Direct prgm link: (URL) Instructions: (URL) Enjoy, and please give me feedback (...) (18 years ago, 16-Apr-06, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Re: BricxCC Feedback Requested
|
|
(...) I've never docked the current toolbars to the side. I wouldn't miss it. (...) I do normally rearrange them (normally to a single row). I'd be annoyed for a few minutes then forget all about it if it was removed :) (...) Personally, I hate the (...) (18 years ago, 16-Apr-06, to lugnet.robotics.rcx.nqc)
|
