 | | Re: NQC/BricxCC test
|
|
(...) Only if active is meant to cause the watch window to quit polling for values if some other BricxCC window is the active window. When graphing this means that after you bring up the graph window you need to click back on the Watch window to (...) (19 years ago, 18-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC/BricxCC test
|
|
(...) Duh! I had 'only if active' ticked and I dont suppose that changes in my light sensor were enough to trigger it. I now have watching the brick & graphing working! I notice that (unused) counter 0 and 1 take on the values of var 0 and 1 and (...) (19 years ago, 18-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC/BricxCC test
|
|
(...) This seems to have fixed all the problems that I was having with the serial tower and Bricx. [It also downloaded new (Swan)firmware OK] The template right-click is great too :-) I wasn't able test out the new (Vers.10) graphing part as I dont (...) (19 years ago, 18-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC/BricxCC test
|
|
I could use some help testing a modification to NQC and BricxCC which is attempting to correct some problems I introduced with the serial IR tower and also the USB tower. Could a few adventurous souls download (URL) and try out the NQC and BricxCC (...) (19 years ago, 14-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC release 3.1r4
|
|
(URL) changed the Spybot program code generation slightly so that it matches that generated by the MindScript compiler. Tasks which are not empty are no longer ended with a Stop Task sequence. Empty tasks are ended (as before) by a Stop Task (...) (19 years ago, 13-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC release 3.1r3
|
|
(URL) a bug in expressions like a = a*2 + a*3; Thanks! John Hansen (19 years ago, 4-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Latest version BrixCC
|
|
(...) I have not yet made an official 3.3.7.9 release of BricxCC. My apologies for the delay. For now you can use the latest version in swan_test.zip. John Hansen (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Latest version BrixCC
|
|
Hi, I found on the sourceforge.net the Brixcc version 3.3.7.7 and in the swan_test.zip the version 3.3.7.9. Is there a newer version? Regards, Jan Kromhout Hellevoetsluis-NL (19 years ago, 27-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: time sampling under the rcx standard OS
|
|
(...) Here's a code byte from my LegWay code. ---- int MotorSpeedArray[32] = {1,3,2,0}; // Speeds // ... later in the program... if (sys_time>CheckTime) // check system timer - is it time to check sensors again? { L1 = ReadSensor(SENSOR_1); L3 = (...) (19 years ago, 21-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: time sampling under the rcx standard OS
|
|
Hi Steve, As I'm quite new to BrickOS and to C programming, I'm sorry I'm not sure I understood what you meant, neither how you do this : (...) - Do you check the sensor at a higher rate, and only send a command to the motor at 1kHz ? - How do you (...) (19 years ago, 21-Sep-05, to lugnet.robotics.rcx.nqc)
|
