 | | Re: LNPD and cygwin
|
|
Nop, actually what I'd like to find out, is if there's some way to make the usb tower work (either on cygwin or linux) for lnpd Thanks in advance, if anyone has the answer CL "nanobapt" <nanobapt@wanadoo.fr> escribió en el mensaje (...) (22 years ago, 20-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LNPD and cygwin
|
|
(...) does lnpd work with usb tower under linux ? nanobapt (22 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | LNPD and cygwin
|
|
Sorry if this message is duplicated, but I got an error when publishing and untin now I don't see it published. Hi all, I have the USB tower so by now (because I have a project for the university, and not too much time) I've to use cygwin. Well (...) (22 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | LNPD and Cygwin
|
|
Hi all, I have the USB tower so by now (because I have a project for the university, and not too much time) I've to use cygwin. Well everthing is running fine, but I came with this question: Is is possible to install LNPD (as a deamon) the same way (...) (22 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | addressing bricks
|
|
Hi everyone, I was wondering if anyone could tell me how to address RCX bricks, using LNP. I have been looking at examples of code on lnp for ages now. Any help would be appreciated. Thanks a lot Andrew ___...___ Hotmail messages direct to your (...) (22 years ago, 13-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Can an input be configured as an output?
|
|
Hi Vik, An input has a 10K pull-up resistor to 5V in it. When nothing is connected to the input the A/D converter will return a value of about 1023 (which represents 5V). If you short the input (make sure it's in passive mode), you will get a value (...) (22 years ago, 11-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Can an input be configured as an output?
|
|
Hi, Im still learning legos (brickOS) and my friend asked me whether an input could be configured as an output? Also, i have seen several robots using 2 RCX, all connected together using wires running from 1 input to anothers output...how does this (...) (22 years ago, 10-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | can't dll with brickOS 2.6.10
|
|
I have been away for quite a while, and when I tried to upgrade to 0.2.6.10 I found that after I firmdl3 (which works, and the RCX works) I am unable to dll (yes, using the included dll, yes, with rebuilt .lx files). I get "error deleting program". (...) (22 years ago, 8-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Problems after upgrading from brickos 0.2.6.09 to 0.2.6.10
|
|
Hello, I hope somebody could help me with the following problem. So far I was using brickos 0.2.6.09 under Windows XP and everything worked fine. I downloaded version 0.2.6.10 and downloaded it's brickos.srec file to the RCX. As soon as I switch on (...) (22 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOs Problem (again)
|
|
(...) Cygwin is pure Windows. DJGPP is DOS, and doesn't work well with brickOS. Although everyone should use Linux. DJGPP and brickOS: I managed to build binutils under djgpp, gcc failed but is probably fixable. However, djgpp doesn't have POSIX (...) (22 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
