 | | Re: LNPD and cygwin
|
|
(...) does lnpd work with usb tower under linux ? nanobapt (21 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | LNPD and cygwin
|
|
Sorry if this message is duplicated, but I got an error when publishing and untin now I don't see it published. Hi all, I have the USB tower so by now (because I have a project for the university, and not too much time) I've to use cygwin. Well (...) (21 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | LNPD and Cygwin
|
|
Hi all, I have the USB tower so by now (because I have a project for the university, and not too much time) I've to use cygwin. Well everthing is running fine, but I came with this question: Is is possible to install LNPD (as a deamon) the same way (...) (21 years ago, 17-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | addressing bricks
|
|
Hi everyone, I was wondering if anyone could tell me how to address RCX bricks, using LNP. I have been looking at examples of code on lnp for ages now. Any help would be appreciated. Thanks a lot Andrew ___...___ Hotmail messages direct to your (...) (21 years ago, 13-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Can an input be configured as an output?
|
|
Hi Vik, An input has a 10K pull-up resistor to 5V in it. When nothing is connected to the input the A/D converter will return a value of about 1023 (which represents 5V). If you short the input (make sure it's in passive mode), you will get a value (...) (21 years ago, 11-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Can an input be configured as an output?
|
|
Hi, Im still learning legos (brickOS) and my friend asked me whether an input could be configured as an output? Also, i have seen several robots using 2 RCX, all connected together using wires running from 1 input to anothers output...how does this (...) (21 years ago, 10-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | can't dll with brickOS 2.6.10
|
|
I have been away for quite a while, and when I tried to upgrade to 0.2.6.10 I found that after I firmdl3 (which works, and the RCX works) I am unable to dll (yes, using the included dll, yes, with rebuilt .lx files). I get "error deleting program". (...) (21 years ago, 8-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Problems after upgrading from brickos 0.2.6.09 to 0.2.6.10
|
|
Hello, I hope somebody could help me with the following problem. So far I was using brickos 0.2.6.09 under Windows XP and everything worked fine. I downloaded version 0.2.6.10 and downloaded it's brickos.srec file to the RCX. As soon as I switch on (...) (21 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOs Problem (again)
|
|
(...) Cygwin is pure Windows. DJGPP is DOS, and doesn't work well with brickOS. Although everyone should use Linux. DJGPP and brickOS: I managed to build binutils under djgpp, gcc failed but is probably fixable. However, djgpp doesn't have POSIX (...) (21 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOs Problem (again)
|
|
(...) You didn't install tar. Run Cygwin setup again and add tar. (...) No, incorrect. (...) No, he needs to install tar. Max. (21 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
