 | | Re: problems with legos on notebook
|
|
Hi Michael, Try the --slow option on firmdl3. This forces it to use the slow download speed, and may help. Also, use --debug to display more debugging info. This may help someone here to work out what the problem is. I'm not sure what the equivalent (...) (23 years ago, 18-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: problems with legos on notebook
|
|
Hallo Ross! This is just the problem, I can not download programs or the legos.srec. Both, firmdl3 and dll give the message "bad ir link". I have an other linux computer on which (with a built in com port) dll and firmdl3 work correctly. I compared (...) (23 years ago, 17-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: problems with legos on notebook
|
|
Michael, I may not be much help as I only use my laptop for downloading programs, not development, and my serial port is built-in. Is there any message when it fails to connect, or not? Does it fail immediately, or timeout after a wait? Do firmdl3 & (...) (23 years ago, 16-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | problems with legos on notebook
|
|
Hallo! Has anybody experiences with legos on notebooks? I want to use legos under linux on a notebook computer. I use a serial pcmcia card from socket communications. The serial port is configured as ttyS0 (irq 4 and io-adr. 0x03f8 are configured (...) (23 years ago, 15-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: ir communication
|
|
(...) Chris (23 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
yes I did ... :-( manuel (...) (23 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | not strictly legOS
|
|
hi all, im doing a research project over here and in the process i have set up lnpd and now have continous communication between my robot and the PC. Now then here is the deal, there is a teoretical posibility that i will get more inputs from my (...) (23 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: WINLNP QUESTIONS
|
|
I did some more digging. When I look into the reg I do not find the reg keys as mentioned on the (URL) page. I dig in the code and set the com port by hand (directly to com1) and now I have the green ligth on the IR tower. However still no messages (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: ir communication
|
|
Yes there is. It is LNP it is availiable for windows or linux. I am just fiddling with the windows version see: (URL) I did not get it working just fine see also my post just before you (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | ir communication
|
|
Hi, i am just doing my first steps with legOS and i want to send some data back to the PC. Is there any kind of software for the PC to read that data and save or display it? TIA Chris (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | WINLNP QUESTIONS
|
|
Dear all, I have some troubles setting up WinLNP. I am new to RCX (2 months) and legOS (1 month) and have not much experience with VC6. I want to set up a line of communication between PC and RCX. I downloaded everything from (URL) and I managed to (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
(...) One other thing, did you erase the firmware from the RCX before trying to load legOS? regards Frank Caggiano "The best education for the best caggiano@crystal-objects.com is the best education for all." (URL) Robert M. Hutchins Logo Users (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
(...) Did you try slow? (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
(...) Did you try using the slow mode option ("-s" for firmdl3) as was suggested? (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
Hi, thanks for the tips, but nothing helps. I tried 0.2.5, I tried the far and near mode, I changed the lighting conditions -> nothing helped. But I don't think that I fired up my Brick/Tower because the original Lego Software under Windows works, (...) (23 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
I use 0.2.5 in windows (djgpp), and can't get by without using the slow download option (-s). If you have lighting problems, perhaps flipping the little switch on the IR tower will help. When I download stuff at school, it helps to have it set to (...) (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
(...) I am using 0.2.4 under windoz and have had similar problems. I found that I must use the slow download option (-s) for the firmware to load properly. regards (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: transfer data failed
|
|
(...) Hi, i use 0.2.5 under Cygwin and sometimes i experience the same problem. I dont think its a problem with the legOS 0.2.4 distribution. The problem often occurs if its too dark or too bright in your room. It also happens if sender and receiver (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | transfer data failed
|
|
Hi there, I use legOS 0.2.4 under Linux and tried (after a few weeks) to download the firmware and get always the follwing error: firmdl3/firmdl: transfer data failed Batteries are brand new, tower was set to short and long dist. nothing helped ... (...) (23 years ago, 6-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Is this an error in legOS 0.2.5?
|
|
(...) a (...) Maybe, if you wanted to be really flash, when you get the (non-ultra) low battery warning, your robot could start seeking out the tower, and get ready to send the data. Maybe have a light near the tower that starts flashing when it (...) (23 years ago, 4-Aug-01, to lugnet.robotics.rcx.legos)
|
