 | | Re: Motor Speed value interpretation?
|
|
In lugnet.robotics.rcx.legos, Rossz Vamos-Wentworth writes: ... (...) hmmm... did your wife figure out what vamos means... you might have to change that one too :-) sorry, but now I don't remember the question about the motor speed (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) My birth name is actually Ross, but I changed it to Rossz when I married my Hungarian wife. In her language it means 'bad'. :) Rossz (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: C++ OverHead
|
|
(...) Hi, unfortunately I am unable to answer your question, however I am very interested in what you are doing with GA. I recently recieved my RCX and have done GA work in the past as part of my schoolwork. I would love to try using some GAs with (...) (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Parallel sensor problem
|
|
Bernardo Dal Seno <piu1759@cdc8g5.cdc.polimi.it> wrote in message news:87d7dd25ge.fsf@...o.bogus... (...) crane, and (...) RCX 2. (...) like: (...) Thanks. I'll try that. (...) happens (...) connected to (...) Nup. I disconnected the motor, but the (...) (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Parallel sensor problem
|
|
(...) I don't know if this is your problem, but the input ports have polarity (one lead is connected to ground and the other to +5V through a resistor, if I remember correctly). Have you tried to change polarities? (...) Maybe the problem is not in (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LegOS 0.2.5 and LNP
|
|
(...) On the RCX the LNP handlers are called from an interrupt handler, so after the execution of lnp_*_set_handler() you can safely assume that the old handler will not be called any more. On a PC things are different, there is a problem. I didn't (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: C++ OverHead
|
|
I seem to recall someone doing some testing that showed that C++ programs worked out to take out somewhere around 2 to 3 times the space of comparable C programs. However, I'm sure that varies. Luis (...) ---...--- "Nobody ever said that democracy (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) As far as I can tell, the speed value really affects power output. This indirectly affects speed, but not in a very happy way. You end up with a wide range of values that give you nearly the same speed, then a very short range that decreases (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | C++ OverHead
|
|
Hi all, a simple question ( I hope) I'm running a small GA on my rcx block , and I'm fairly happy qwith my results so far, it evolves well tot he conditions, however I'd like to try something new <g>... I'm going to try to evolve sub-sumptive (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Parallel sensor problem
|
|
Hi, all. I'm experiencing a strange problem. I'm using two RCXs to control my crane, and I have a single touch sensor connected to input 1 on RCX 1 & input 2 on RCX 2. However, when I run both programs, which both have a wait_event function like: (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
