 | | Re: I played with fire...
|
|
Well, Philo did it again, Hourrah for him... I bypassed the fuse and the RCX came back to life. Now, will I be carefull enough with my RCX without a fuse or should I replace it ? (17 years ago, 2-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:Jnp0Cy.2CJ@lugnet.com... (...) This X axis gear box is loaded so there is no backlash. The 16T gear on the right side has a hole through it and is fixed to the shaft with a serrated half (...) (17 years ago, 1-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
(...) 16t gear to the gear rack on the bottom of the table. also, the z axis seems to use an idler gear. that's exactly the setup i've built, you can see it here: (URL) top left, next to the tool changer idea (right next to the tiny word "tool"). i (...) (17 years ago, 1-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnMwFu.CMs@lugnet.com... (...) I like the worm for a drive. It provides the best ratio and the least backlash. It also acts as a brake while the slide is under the pressure returned by (...) (17 years ago, 31-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
ok, now i understand what you mean. the problem is that this setup could be difficult for long axes, i guess the axle with the worm gears would flex too much... (...) exactly what i was thinking. that's the way the machines i've seen change their (...) (17 years ago, 31-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnL3ox.7r9@lugnet.com... (...) As you can see, I do not know how to get "deep links" on Brick Shelf. If I figure it out I will post the links again. The tools can ride a disk in front of (...) (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnL3ox.7r9@lugnet.com... (...) (URL) Hope I did this right. Bob (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
(...) indeed, i agree! (...) i can't quite picture what you mean. could you upload a drawing or something? the animation you sent is good, actually the up/down movement it makes could be the z-axis itself, saving me another motor (not the tool (...) (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"Bob Fay" <rgfay@earthlink.net> wrote in message news:JnKABC.F5v@lugnet.com... (...) I was successful reaching your page. It answers my questions about configuration. I am sure you will agree with me that Lego should have made a rack gear that (...) (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnJLtv.G5y@lugnet.com... (...) That should be possible. I am thinking of parafin (sp?). That is a lot different. Worth a try. (...) Not able to recycle. Might even cause global warming. (...) (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
